Specifications; Additional Safety Rules For Tool - Makita BFT120 Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Button
3 Red part
4 Indicating lamp
5 Capacity
6 Switch trigger
7 Light

SPECIFICATIONS

Model
–1
No load speed (min ).....................................320
Fastening torque .............................................5 – 12 N•m
Dimensions .....................................................174 mm x 65 mm x 256 mm
Net weight .......................................................1.3 kg
Rated voltage ..................................................D.C. 9.6 V
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES FOR TOOL

1. Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will also make exposed metal parts of the
tool "live" and shock the operator.
3. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS- This manual con-
tains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION - To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4
Explanation of general view
8 Reversing switch lever
9 LED indicator
10 Graduations
11 Adjusting grip
12 Bit
13 Sleeve
14 Revolution angle (°)
BFT120/BFT120F
(with battery cartridge BH9020)
4.
5.
6.
7.
8.
9.
ENB026-1
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
14. If operating time has become excessively
ENC002-3
15. If electrolyte gets into your eyes, rinse them out
15 Capacity limit of BFT120 (F)
16 Battery 20°C
17 Torque N•m (in. lbs)
18 Capacity limit of BFT121 (F)
19 Limit mark
20 Brush holder cap
21 Screwdriver
BFT121F
340
5 – 12 N•m
174 mm x 65 mm x 265 mm
(with battery cartridge BH1220)
1.5 kg
D.C. 12 V
Do not expose charger to rain or snow.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
Do not operate charger with damaged cord or
plug - replace them immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.