Battery Charging - Bosch Indego 850 Originalbetriebsanleitung

OBJ_BUCH-1573-008.book Page 42 Tuesday, October 27, 2015 10:35 AM
42 | English
Logicut Intelligent Cutting
How the Indego cuts efficiently (see figure 20)
To mow efficiently the Indego learns the shape of the cutting
area it is working in. This learning occurs during the first two
cutting cycles.
Below is an explanation of how the Indego learns the lawn
shape.
How it works
To mow efficiently the Indego maps the outline of the lawn ar-
ea and the location of the objects within it (trees, flowerbeds,
ponds, etc) that are marked out with perimeter wire during in-
stallation. This allows the Indego to plan where it needs to cut
the grass, where it has cut the grass and also its route to and
from the docking station. This allows the Indego to complete
the task of mowing more efficiently.
Mapping the cutting area (see figure 20)
After setup the Indego will first map out the shape of the gar-
den. This is done by following the perimeter wire placed
around the edge of the garden. Whilst following the perimeter
wire the Indego is measuring the distances. The Indego then
builds up a map of the garden that is saved into its memory.
Note: The Indego does not follow the wire to the inner bound-
aries.
Learning the location of garden objects marked
out with the perimeter wire (see figure 20)
Once the Indego has the cutting area mapped it can start to
cut the grass. After pressing "Mow Now" the Indego will leave
the docking station and start to cut the grass in parallel lanes.
For accuracy the parallel lanes are limited to approximately
10 m. It will continue cutting in these lanes until it completes
a section of the cutting area or until it discovers an object that
has been marked out using the perimeter wire.
Once an object is discovered the Indego will follow the perim-
eter wire around it to establish its shape. The Indego will then
drive to the perimeter wire at the edge of the cutting area to
confirm the location of the object within the garden map. The
Indego will then continue mowing. This process will be repeat-
ed if the Indego discovers additional objects whilst mowing.
The Indego will complete the mowing then return to the dock-
ing station.
Note: This process will be continued the 2nd time the Indego
cuts the grass. This is to make sure that all objects in the gar-
den are discovered and their location on the garden map is
accurately logged.
If there are no more objects in the garden the Indego will con-
tinue to cut the grass as normal.
In case a new inner boundary (e. g. flower bed) should be
marked up after the installation is complete, this can be done
by adding extra cable with a wire connector. (see figure 10)
F 016 L81 517 | (27.10.15)
Mowing mode (see figure 20)
Once the Indego has learnt the location of all the objects in the
garden it will mow the garden in an efficient parallel lane pat-
tern.
Dual Speed Cutting
If the Indego encounters deep or thick grass whilst cutting it
will automatically increase the RPM of the cutting system and
slow the drive speed until it has cut the area of higher grass.
Border Cutting Mode
The Indego will cut around the perimeter wire. The frequency
of the border cut can be selected. The default is set to every
fourth cutting slot.
Cutting Lane Proximity
The Indego cuts the lawn using parallel lanes up to 10 m in
length. The distance between the lanes is set to 20 cm but will
be reduced automatically if the grass height increases. Once
the grass is cut the Indego will return to the default distance
between the lanes. This setting can be adjusted by the user in
the Indego menu.
Sensors
The machine has following sensors:
– lift sensor, will be activated if the machine is lifted and
cause the machine and cutting blades to stop
– roll over sensor, will detect when the machine is inverted
and cause the machine and cutting blades to stop
– obstruction sensor, tactile detection for obstacle any-
where in the full width of the path of the machine and cause
the machine to change its direction
– tilt sensor, will be activated if the machine reaches an an-
gle of 45°
If one of the sensors is activated, such as lift sensor, the
screen will show a message, e. g. "Machine has been lifted.
Please enter PIN code to continue". The display switches into
sleep mode, if no input is made for 10 minutes. Press any but-
ton to reactivate the screen.
If the machine is in sleep mode, press any button to change to
the PIN entry screen and enter the PIN code.

Battery Charging

The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 5 °C
and 45 °C.
The lithium-ion battery is supplied partially charged. To en-
sure full capacity of the battery, completely charge the ma-
chine in the docking station before first use.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
When the battery is run down or discharged, the machine is
shut off by means of a protective circuit: the blade no longer
moves.
Bosch Power Tools