Noise/Vibration Information; Declaration Of Conformity; Battery Charging - Bosch ROTAK 34 LI Originalbetriebsanleitung

OBJ_BUCH-882-001.book Page 26 Friday, November 14, 2008 7:42 AM
26 | English

Noise/Vibration Information

Rotak 34/37 LI
Measured values determined according to
2000/14/EC (1.60 m height, 1.0 m distance
away) and EN ISO 5349.
Typically the A-weighted noise levels of the
product are: Sound pressure level 8 1 dB(A);
Guaranteed sound power level lower than
9 0 dB(A). Uncertainty K =0 .74 dB.
The hand-arm acceleration is typically below
2
2.5 m/s .
Rotak 43 LI
Measured values determined according to
2000/14/EC (1.60 m height, 1.0 m distance
away) and EN ISO 5349.
Typically the A-weighted noise levels of the
product are: Sound pressure level 8 1 dB(A);
Guaranteed sound power level lower than
9 1 dB(A). Uncertainty K =0 .74 dB.
The hand-arm acceleration is typically below
2
2.5 m/s .

Declaration of Conformity

Rotak 34/37 LI
We declare under our sole responsibility that
the product described under "Technical data" is
in conformity with the following standards or
standardization documents: EN 60335, EN
50338 (battery powered product) and EN
60335 (battery charger) according to the
provisions of the directives 2006/95/EC,
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009), 2000/14/EC.
2000/14/EC: Measured sound power level 9 0
dB(A). Conformity assessment procedure
according to Annex VI.
Rotak 43 LI
We declare under our sole responsibility that
the product described under "Technical data" is
in conformity with the following standards or
standardization documents: EN 60335, EN
50338 (battery powered product) and EN
60335 (battery charger) according to the
provisions of the directives 2006/95/EC,
F 016 L70 576 | (14.11.08)
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009), 2000/14/EC.
2000/14/EC: Measured sound power level 9 0
dB(A). Conformity assessment procedure
according to Annex VI.
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
2008
Leinfelden, 17.09.2008
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
17.09.2008, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
For Your Safety
Warning! Switch off, remove the isolator
key and the battery before adjusting, clean-
ing or if cable is cut, damaged or entangled.
The blades continue to rotate for a few sec-
onds after the machine is switched off.
Caution – do not touch the rotating blade.

Battery Charging

Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the unit. Equip-
ment marked with 230 V can also be connected
to 220 V or 240 V.
Use only the charging unit supplied. Only this
charging unit is matched to the lithium-ion bat-
tery used in the product.
Bosch Power Tools