Maintenance - Makita UC120D Betriebsanleitung

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Always wear gloves when performing any inspection or
maintenance.
• Please have your saw chain sharpened at a Makita
Authorized Service Center or replace with a new one if
your saw chain does not cut correctly.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning guide bar (Fig. 16)
Chips and sawdust will build up in the guide bar groove,
clogging it and impairing oil flow. Always clean out the
chips and sawdust when sharpening or replacing the saw
chain.
Storing tool
Clean the tool before storing. Remove any chips and
sawdust from the tool after removing the chain cover.
After cleaning the tool, run it under no load. Then remove
the battery cartridge from the tool and lubricate the saw
chain and guide bar.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Various type of Makita genuine batteries and chargers
• Saw chain
• Scabbard
• Guide bar complete
• File
• Hex wrench
• Chain oil
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3.38 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: cutting wood
Vibration emission (a
Uncertainty (K): 2.6 m/s
12
ENG905-1
): 80 dB (A)
pA
ENG900-1
2
): 8.9 m/s
h
2
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufac-
turer declare that the following Makita machine(s):
Designation of Machine: Cordless Chain Saw
Model No./ Type: UC120D
Specifications: see "SPECIFICATIONS" table.
are of series production and
Conforms to the following European Directives:
2000/14/EC, 2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorized
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, MK15 8JD, England
The conformity assessment procedure required by Direc-
tive 2000/14/EC was in Accordance with annex V.
Measured Sound Power Level: 90 dB
Guaranteed Sound Power Level: 94 dB
14. 10. 2009
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
Director
ENG901-1
ENH021-5