Before Starting The Equipment; Installing The Machine - EINHELL BT-BD 801 E Originalbetriebsanleitung

Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

5.1.Installing the machine

•
Place the base plate (1) in the desired posi-
tion.
•
Fasten the pillar (2) with flange using the sup-
plied bolts (A) (Figs. 3 - 4).
•
You can now fit the table and clamp in place
with the clamping lever. Following this, fit the
crank (27) and fasten tightly with the screw
(28). (Fig. 5-7)
•
Anl_BT_BD_801_E_SPK1.indd 25 Anl_BT_BD_801_E_SPK1.indd 25
GB
•
Finally, fit the complete bit head to the pillar.
Align the head so that it is horizontal to the
base plate and fasten it in position with the
screws (35). (Fig. 8-9)
•
Screw the 3 supplied handles (9) in the hand-
le mounts. (Fig. 10).
•
Screw in the speed control lever (15) as
shown in Figure 11.
•
Secure the roller support (3) with thumb
screws (21) (Fig. 12).
•
Before you mount the drill chuck with the
MK shank, check that both parts are clean.
Insert the taper mandrel in the taper of the
drill chuck with a powerful jolt. Then insert
the taper in the spindle. To do this, place the
drill chuck (10) with taper (24) in the spindle
(11) and guide it to the stop point, then turn
the chuck until it slips a little further into the
spindle (11). Insert the drill chuck (10) with
taper (24) into the spindle (11) with a jolt and
check that the chuck is secure (Figs. 13 - 14).
Important: All bare parts are greased in order to
protect them from corrosion. Before mounting the
drill chuck (10) onto the spindle (11), both parts
must be completely degreased using an environ-
mentally friendly solvent. This ensures optimal
transmission of power.
5.2. Installing the machine
Before you use the drill for the fi rst time it must be
mounted in a stationary position on a fi rm surface.
Use both mounting holes (12) in the base plate to
do this. Ensure that the machine is freely acces-
sible for operation, adjustment and maintenance.
Important: The fi xing screws may only be tighte-
ned to a point where they do not distort or deform
the base plate. Excessive tension can lead to
fracture.
5.3. Folding chip guard (Figs. 15 - 17)
Mount the folding chip guard (13) as shown in
Figures 15 and 16.
The height of the cover (23) is infi nitely adjustable
and can be locked using both thumb screws (22).
The chip guard (13) can be fl ipped up to enable
bits to be changed.
5.4. Prior to starting
Ensure that the voltage of the mains supply com-
plies with the specifi cations on the rating plate.
Connect the machine only to a socket with the
properly installed earthing contact.
The table drill is equipped with a no-volt trip that is
designed to protect the operator from an undesi-
- 25 -
02.08.12 11:22 02.08.12 11:22