Hammer Drilling In Concrete (Additional Handle); Before Starting The Equipment - EINHELL TC-ID 550 E Originalbetriebsanleitung

L sound pressure level ........................ 91 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 102 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Hammer drilling in concrete (handle)
Vibration emission value a
K uncertainty = 1.5 m/s
Hammer drilling in concrete
(additional handle)
Vibration emission value a
K uncertainty = 1.5 m/s
Drilling in metal (handle)
Vibration emission value a
K uncertainty = 1.5 m/s
Drilling in metal (additional handle)
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anleitung_TC_ID_550_E_SPK1.indb 16 Anleitung_TC_ID_550_E_SPK1.indb 16
= 14.44 m/s
2
h, ID
2
= 10.59 m/s
2
h, ID
2
= 4.09 m/s
2
h, D
2
= 2.53 m/s
2
h, I
2
- 16 -
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1. Fitting the additional handle
(Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop (Fig.
4/Item 2)
The depth stop (2) is held in place by the additi-
onal handle (8) by clamping. The clamp can be
released and tightened by turning the handle.
•
Release the clamp and fit the depth stop (2)
10.11.2016 07:28:29 10.11.2016 07:28:29