Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts - EINHELL BT-BD 801 E Originalbetriebsanleitung

7. Replacing the power cable

If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Warning!
Pull out the power plug before carrying out any
adjustments, maintenance or repairs.
8.1 Cleaning
•
The table drill is to a large extent mainte-
nance-free. Keep the device clean. Pull out
the mains plug before doing any cleaning and
maintenance work on the machine. Do not
use any harsh, abrasive cleaning solvents.
Ensure that no liquid seeps into the device.
Regrease all bare parts when the work is
finished. The drill pillar, blank parts of the
column, and the drill table especially should
be regreased at regular intervals. Use a stan-
dard, acid-free lubricating grease to do this.
Caution: Do not use your household refuse
bin as a receptacle for oil and grease-soaked
cleaning rags or grease and oil sludge. Dispo-
se of these toxic materials in an environmen-
tally-friendly fashion. Regularly check and
clean the ventilation holes. Store the device
in a dry room. Should the device become
damaged, do not try to repair it yourself; leave
this work to the hands of a qualified electrical
technician.
•
We recommend that you clean the device
•
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
Anl_BT_BD_801_E_SPK1.indd 28 Anl_BT_BD_801_E_SPK1.indd 28
GB
8.2.1 Changing the V-belt (Figs. 26 - 28)
The V-belt of the pillar drill is a wear part and
should be replaced when worn. Proceed as fol-
lows:
•
Run the machine run in idle mode while slow-
ly setting the speed adjustor lever (15) to the
minimum speed (see point 7.5).
•
Switch the machine off, then pull the power
plug.
•
Set the speed adjustor lever (15) to the maxi-
mum speed setting to slacken the
•
V-belt.
•
Undo the screw (16) to open the V-belt cover
(7).
•
Pry the V-belt (39) off of the drive pulley (38)
by pulling up the belt on one side and slowly
turning the pulley (38). The drive pulley (38)
comprises two disks that are pressed to-
gether via a spring. If the V-belt (39) does not
exhibit enough play to remove it, gently press
the bottom half of the drive pulley (38) down
to slacken the V-belt (39).
•
Fit one end of the new V-belt (39) to the vari-
able pulley (40). Fit the other end to the drive
pulley (38) by first sliding it into the groove on
one side of the pulley (38) , then prying the V-
belt (39) across the pulley into the groove on
the other side.
•
Close the V-belt cover and screw down using
the screw (16).

8.3 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
- 28 -
02.08.12 11:22 02.08.12 11:22