Hot Water - Saeco Nina Plus Bedienungsanleitung

coff ee brewing, then remove the coff ee cup.
• (Fig.16) - Wait a few seconds after brewing, then remove
the portafi lter and dispose of the used pod.
Important note: The fi lter (14) and the adapter
(13) should be kept clean to guarantee perfect
results. Clean daily after use.
6 TIPS FOR CHOOSING COFFEE
As a general rule any type of coff ee available on the market can
be used. However, coff ee is a natural product and its fl avour
changes according to its origin and blend; it is therefore a good
idea to try diff erent types of coff ee in order to fi nd the most
suited to your personal taste.
For optimal results, however, we recommend using espresso
machine blends. As a rule, Coff ee should always come out of the
portafi lter without any dripping.
The speed of coff ee dispensing can be modifi ed by slightly
changing the amount of coff ee in the fi lter and/or by using a
diff erent coff ee grind.
Saeco recommends using single-dose coff ee pods marked ESE
for a tasty coff ee and easier cleaning and preparing.
BEFORE USING THE HOT WATER/STEAM JET, MAKE
SURE THAT THE STEAM SPOUT (PANNARELLO) IS
POSITIONED OVER THE DRIP TRAY.
7

HOT WATER

Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
• (Fig.3) - Press the ON/OFF button (2).
• Wait until the "machine ready" light (15) turns on. The ma-
chine is now ready.
• (Fig.18) - Place a container or a teacup under the steam
spout (Pannarello).
• (Fig.5) - Open the knob (4).
• (Fig.6) - Switch the selection knob to the "
(17).
• When the desired quantity of hot water has been dispensed,
set the selection knob (17) to the " " position.
• (Fig.5) - Close the knob (4).
• Remove the container with hot water.
• 18 •
8 STEAM / CAPPUCCINO
Danger of scalding! When brewing starts, spurts
of hot water may come out. The spout can reach
high temperatures: do not touch it with bare hands.
• (Fig.3) - Press the ON/OFF button (2).
• Wait until the "machine ready" (15) light turns on.
• (Fig.19) - Switch the selection knob (17) to the " " posi-
tion.
• Wait until the light (16) turns on. The machine is now ready
for steam ejection.
• (Fig.18) - Place a container under the steam spout.
• (Fig.5) - Open the knob (4) for a few seconds, so that re-
maining water fl ows out of the steam spout (Pannarello). In
a short time only steam will come out.
• Close the knob (4) and remove the container.
• Fill 1/3 of the container you wish to use to prepare your cap-
puccino with cold milk.
Use cold milk to get a better result.
• (Fig.20) - Immerse the steam spout in the milk and open the
knob (4) by turning it anticlockwise. Turn the milk container
with slow upward movements so that it warms up evenly.
A maximum steam brewing of 60 seconds is rec-
ommended.
• When brewing ends, close the knob (4) and remove the cup
with the frothed milk.
• (Fig.19) - Switch the selection knob (17) to the " " posi-
tion.
If both lights are on and the machine has reached a too high
temperature to brew coff ee, prime the circuit as described in
section 4.5 to make the machine ready for use.
Note: The machine is ready when the "machine
ready" light (15) is permanently on.
Note: If brewing a cappuccino as described is not
possible, prime the circuit as explained in Sec-
tion.5, then repeat the procedure.
The same procedure can be used to heat other
beverages.
" position
• After this operation, clean the steam spout with a wet cloth.