Starting Operation; Working Advice - Bosch EXACT ION 2-700 Originalbetriebsanleitung

OBJ_BUCH-1781-003.book Page 17 Wednesday, March 4, 2015 10:40 AM
Battery Charge-control Indication (yellow LED)
Battery Charge- Meaning
control Indica-
tion 7
Flashing light + Battery Charging:
audio signal Only 6–8 more screwdriving operations
possible.
Continuous light Capacity no longer sufficient for a new
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
Flashing light The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative
humidity between 20 and 95 %, free of moisture condensa-
tion.
Suspension Device (see figure B)
With the utility clip 11, the machine can be attached to a sus-
pension device.
– Fasten the utility clip 11 to the machine by engaging it into
the fastening slots 12.
 Regularly check the condition of the utility clip and the
hook of the suspension device.
Configuring the Power Tool
With the BOSCH EXACT Configurator software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Changing the Tool (see figure C)
 When working with an application tool, pay attention
that the application tool is firmly seated on the tool
holder. When the application tool is not firmly connected
with the tool holder, it can come loose again and not be
controlled.
Inserting
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
– Pull the sleeve of quick-change chuck 2 to the front and
hold.
– Insert tool bit 13 into tool holder 1 and release the quick-
change chuck.
Bosch Power Tools
Removing
– Pull the sleeve of quick-change chuck 2 to the front and
hold.
– Remove tool bit 13 from tool holder 1 and release the
quick-change chuck.
Operation
 Before any work on the power tool, remove the battery.

Starting Operation

When starting the power tool, you should first select the di-
rection of rotation with the rotational direction switch 6 since
the power tool starts only when the rotational direction switch
6 is not in the middle position (switch-on lock).
Reversing the rotational direction (see figure D)
– Right rotation: For driving in screws, push the rotational
direction switch 6 left to the stop.
– Left Rotation: For loosening or unscrewing screws, push
the rotational direction switch 6 right to the stop.
Switching On the Worklight
The work area illumination 3 makes possible the lighting of
the screwing position for unfavorable light conditions. The
work area illumination 3 is switched on by lightly pressing the
on/off switch 5. When the on/off switch is firmly pressed, the
power tool is switched on and the work area illumination con-
tinues to light.
 Do not look directly into the work area illumination –
your sight can be temporarily degraded!
Switching On and Off
The screwdriver have a shut-off clutch that
depends on the torque and can be set in the
given range. It responds when the torque that
is set is reached.
– To start the machine press the on/off switch 5 to the stop.
– The machine switches off automatically as soon as the
preset torque is reached.
 When the on/off switch 5 is released prematurely, the
preset torque is not reached.
To save energy, only switch the power tool on when using it.

Working Advice

 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.
Setting the Torque (see figure E)
The tightening torque is dependent on the spring pretension
of the shut-off clutch. The shut-off clutch responds in right as
well as left rotation when the torque setting is reached.
For setting the individual tightening torques, use only the ad-
justment tool 14 provided.
– Push the torque selector switch 4 on the power tool com-
pletely back.
– Insert the adjustment tool 14 into the tool holder 1 and
turn it slowly.
English | 17
1 609 92A 137 | (4.3.15)