Starting Operation - Bosch GTB 185-LI Professional Originalbetriebsanleitung

14 | English
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Remove the depth stop (4) from the power tool. Pull the
screwdriver bit (1) out. If required, the universal bit
holder (14) can also be pulled out and replaced. Use a pair
of pliers if necessary.
After changing the tool, reattach the depth stop (4).
Operation

Starting Operation

Inserting the battery
Note: The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch (5) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (7) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figures E–F)
The rotational direction switch (5) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (12) is being pressed.
Clockwise: Slide the rotational direction switch (5) on
the left-hand side of the power tool towards the front
of the power tool. The rotational direction switch (5)
1 609 92A 6HJ | (23.09.2021)
Capacity
60−100 %
30−60 %
Switching on/off
5−30 %
To start the power tool, press and hold the on/off switch
0−5 %
(12).
The LED lights up when the on/off switch (12) is lightly or
fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
Press the lock-on button (6) to lock the on/off switch (12) in
this position.
Capacity To switch off the power tool, release the on/off switch (12);
or, if the switch is locked with the lock-on button (6), briefly
80−100 %
press the on/off switch (12) and then release it.
60−80 %
Adjusting the Speed
40−60 %
You can adjust the speed of the power tool when it is on by
20−40 %
pressing in the on/off switch (12) to varying extents.
5−20 %
A light pressure on the on/off switch (12) results in a low ro-
0−5 %
tational speed. Increased pressure on the switch causes an
increase in speed.
Screwing in Screws
To screw in screws place the screw on the screwdriver bit
(1). The screw will be held in place by the magnetic reten-
tion force of the universal bit holder (14). Slide the rota-
tional direction switch (5) on the left-hand side of the power
tool towards the front of the power tool. Switch the power
tool on and push the tip of the screw firmly against the work-
piece. The screw is screwed into the workpiece until it
reaches the set screw-in depth. The reversible depth
stop (4) touches the workpiece and the drive is switched off;
the universal bit holder (14) stops turning. Check the screw-
in depth and readjust the reversible depth stop (4) if neces-
sary.
Adjusting the Screw-in Depth (see figure B)
The depth to which the screw head is screwed into the work-
piece can be preset by turning the adjusting sleeve (3).
clockwise decreases the screw-in depth. Turning the adjust-
ing sleeve (3) beyond the MAX position will remove it from
the stop sleeve (2) completely.
The best way to determine the setting you require is to drive
in some test screws.
on the right-hand side of the power tool automatically
slides backwards.
Anticlockwise: Slide the rotational direction switch
(5) on the left-hand side of the power tool backwards
(i.e. away from the front of the power tool). The rota-
tional direction switch (5) on the right-hand side of the
power tool automatically slides forwards.
Turn the adjusting sleeve (3) to the position of
your required screw-in depth. The number on
the scale (visible on the edge of the adjusting
sleeve (3)) can be used as a guide for your re-
quired screw-in depth.
Turning the adjusting sleeve (3) clockwise in-
creases the screw-in depth; turning it anti-
Bosch Power Tools