Noise/Vibration Information; Starting Operation - Bosch GSR 6-60 TE Professional Originalbetriebsanleitung

12 | English
Screwdrivers
No-load speed
Rated speed
Tool holder
Max. screw diameter
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level
sound power level
uncertainty K
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K determined according to EN 62841-2-2:
h
Screwdriving:
a
h
K
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
1 609 92A 7YL | (13.06.2022)
GSR 6-45 TE
rpm 0–5 000
rpm 0–3 000
¼" internal hexagon
mm
kg
GSR 6-25 TE
dB(A)
dB(A)
dB
2
m/s < 2.5
2
m/s
Changing the Tool (see figure A)
Pull the screw depth stop (4) off towards you. Pull the
screwdriver bit (1) out. If required, the universal bit
holder (10) can also be pulled out and replaced.
After changing the tool, reattach the screw depth stop (4).
Operation

Starting Operation

Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Setting the Rotational Direction
The rotational direction switch (8) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (7) is being pressed.
– Clockwise: To drive in screws, press the rotational direc-
tion switch (8) through as far as possible to the left.
– Anti-clockwise: To loosen or unscrew screws, press the
rotational direction switch (8) through as far as possible
to the right.
GSR 6-60 TE
0–6 000
0–4 500
¼" internal hexagon
6 6
1.4 1.4
/ II / II
GSR 6-45 TE
81 79
92 90
3 3
< 2.5
1.5 1.5
GSR 6-60 TE
0–6 500
0–4 500
¼" internal hexagon
6
1.4
/ II
GSR 6-60 TE
81
92
3
3.3
1.5
Bosch Power Tools