Assembly Of The Pasta Attachments (See Fig. E); Attach Preassembled Worm Housing; Operation Of The Meat Grinder; Complete Operation - BOMANN KM 1395 CB Bedienungsanleitung

Assembly of the Pasta Attachments (See Fig. E)

NOTE:
If the pasta dough is very sticky, lubricate the worm with a
few drops of cooking oil.
Proceed as described under "Preparation".
6. Select a pasta attachment (34).
7. Place the attachment on the axis of the spiral. Pay atten-
tion to the recesses on the pasta attachment.
More details can be found under "Attach Preassembled
Worm Housing".

Attach Preassembled Worm Housing

8. Screw the locking ring (28) clockwise onto the spiral
housing.
9. Attach the pre-assembled worm housing to the appliance.
Position the worm housing with the arrow (
with ( ) on the appliance. Turn to the upright position.
The arrow on the worm housing must be opposite the
arrow on the appliance. (Refer to the figure.)
CAUTION:
If you open and close the ring nut again after attaching
it, hold the worm housing securely with one hand on
the filler neck (23), otherwise the worm housing may
accidentally come loose.
10. Position the filler tray (22) so that the bed of the tray lies
above the arm (7).

Operation of the Meat Grinder

WARNING: Risk of injury!
• Once you turn on the appliance, the drive shaft of the
kneading machine starts rotating. Do not reach into the
rotating drive shaft during operation!
• Always mount the bowl for your safety.
• Always use the supplied pusher. Never put fingers or
tools into the filler neck!
CAUTION:
Never use the meat grinder with attached bowl! Cover the
drive shaft of the mixing drive with the safety cover (6).
11. Put the pieces of meat (meat paste / sausage mass or
dough) on the filling tray and into the filler neck.
12. Plug the power cord into a properly installed earthed
socket.
13. You can select a speed from level 4 to 8.
14. Stuff, if necessary, the meat respectively the dough with
the stuffer (21).
62
KM1395CB_IM
NOTE:
Short-term operation: Operate the appliance with the
meat grinder no longer than 10 minutes and allow the
appliance to cool down for 10 minutes.

Complete Operation

1. Turn the rotary knob anticlockwise until the display shows
" ".
2. Disconnect the power plug.
3. Disassemble all parts of the meat grinder.
4. Clean the parts used as described under "Cleaning".
5. Cover the uptake for the spiral housing with the cover (15).

Application Instruction for the Mixer

) aligned
WARNING: Risk of injury!
The knife in the mixer is sharp! Handle the blades
•
of the mixer with the necessary care, especially when
emptying and cleaning the mixing bowl!
• Once you turn on the appliance, the drive shaft of the
kneading machine starts rotating. Do not reach into the
rotating drive shaft during operation!
• Always mount the bowl for your safety.
CAUTION:
• Never press the release button (10), if you have placed
the mixing bowl! The mixing bowl tilts.
• Do not operate the mixer without food!
• The glass could crack at high temperatures! Do not fill
in liquids over 60 °C.
• Do not overfill the mixing bowl! Fill in a maximum of
1500 ml (fruit and liquid).
• Foam takes a lot of volume. Reduce the capacity for
liquids that foam vigorously.
• Cut the food into small pieces before operating the
appliance.
• Do not fill any hard ingredients such as nuts or coffee
beans into the mixing bowl.
• Objects like spoons or scrapers never may be in the
mixing vessel during operation.
NOTE:
The knives in the mixing vessel are also suited to crush
small amounts of pure ice. Remember, however, that the
operation may blunt the knife.
Recommendation:
If you want to prepare drinks with crushed ice, add the ice
cubes during mixing. The ice is crushed during mixing.
Place the mixing bowl on a stable level surface when filling it.
So you can better place the cover afterwards.

The Mixer

22.06.17