Safety Precautions; Extension Cords - Makita ELM3310 Original Bedienungsanleitung

Model:
Grass catcher:
Net weight:
Degree of protection against liquid:
Height adjustment:
5. ASSEMBLY
5-1 ASSEMBLY THE WHEEL (Fig. 2)
Put the axle of the rear wheel cover (the bigger one) insert
the wheel and screw into the hole of the rear wheel
support. Fix the small wheel in the same way.
WARNING: All wheels must be at the same
height.
5-2 ASSEMBLY THE FOLDING HANDLE
A) Insert the lower handlebars into the fixed holes of the
underpan, and then fix them with supplied screw by a
screwdriver. (Fig. 3 & 4)
B) Release the upper handlebars for folding. Connect the
upper handle and the lower handle with the locking
lever. (Fig. 5 & 6)
C) Position the cable over the handle shaft. Clamp it
around the middle of lower handle by the cable clamp
so that the cable is fixed on the outside of the
machine. Otherwise the cable may be pinched by
opening/closing the rear cover. (Fig. 7)
5-3 ASSEMBLY THE GRASS CATCHER
1. To fit: Raise the rear cover and hitch the grass catcher
on rear of mower. (Fig. 8 - 10)
2. To remove: Grasp and lift the rear cover, remove
grass catcher.
5-4 ADJUSTMENT OF CUTTING HEIGHT
The cutting height is adjusted by attaching the wheels to
the required hole.
All wheels must be at the same height.
The height (the blade to the ground) can be adjusted from
20 mm (the lowest position) to 55 mm (the highest
position), 3 height positions (20 mm/40 mm/55 mm).
WARNING: Make this adjustment only when the
blade is stopped.

6. SAFETY PRECAUTIONS

a) Always operate with the deflector or grass catcher in
the correct position.
b) Always stop the motor before removing the grass
catcher or adjusting the height of cutting position.
c) Before mowing, remove all foreign objects from the
lawn which may be thrown by the machine. While
mowing, stay alert for any foreign objects which may
have been missed. (Fig. 11)
d) Never lift the rear of the mower while starting the
motor or during normal operation. (Fig. 12)
e) Always ensure that the ventilation openings are kept
clear of debris.
ELM3310
27 L
13.1 kg
IPX4
20/40/55 mm, 3 adjustment
f) Never place your hands or feet underneath the
underpan or into the rear discharge chute while the
motor is running. (Fig. 13)
7. STARTING
Before connecting up the lawn mower to the electric
power supply, make sure that the mains supply voltage is
230 V – 50 Hz. When the lawn mower power on, the
indicator light will turn on (Fig. 14).
Start the motor as follows (Fig. 15).
a) Press the safety push-button (1).
b) And meanwhile, pull the switch handle (2),and keep it
in grasp.
Push the lawn mower manually when the motor is
running.
If you release the switch handle, the motor will stop.
the motor is started.
after the motor is switch off.
8. BLADE
The blade is made of pressed steel. It will be necessary to
reshape it frequently (with a grind wheel).
Ensure that it is always balanced (an unbalanced blade
will cause dangerous vibrations). To check for balance,
insert a round rod through the central hole and support
the blade horizontally. (Fig. 16) A balance blade will
remain horizontal. If the blade is not balanced the heavy
end will rotate downwards. Reshape the heavy end until
the blade is currently balanced. (Fig. 17) To remove the
blade (2), unscrew the blade screw (3). (Fig. 18 - 20)
Check the conditions of the fan(1), and replace any parts,
which are damaged. (Fig. 18)
When reassembling, make sure that the cutting edges
face in the direction of the motor rotation. The blade screw
(3) must be tightened to 20 -25 Nm torque.
MAKITA 263001422 (for ELM3310) and MAKITA
263001414 (for ELM3710) only.

9. EXTENSION CORDS

You should only use extension cords for outdoor use,
PVC (H05VV-F) or rubber cord (H05RN-F) ordinary duty
with a cross sectional area not less than 1.5 mm
Before using, check the supply and extension cords for
signs of damaged during use, disconnect the cord for
signs of damage or aging. If the cord becomes damaged
20/40/55 mm, 3 adjustment
CAUTION: The blade starts turning as soon as
WARNING: Cutting elements continue to rotate
WARNING: For service, replace the blade with:
ELM3710
35 L
14.8 kg
IPX4
2
.
9