Specifications - Makita 6216D Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Battery charger
5 Bit
6 Tighten
7 Sleeve
8 Ring
9 Bit holder

SPECIFICATIONS

Model
Capacities
Steel .................................................... 10 mm
Wood ................................................... 30 mm
Wood screw ......................................... 6 x 75 mm
Machine screw .................................... 6 mm
-1
No load speed (min )
High ..................................................... 0 – 1,300
Low ...................................................... 0 – 400
Overall length ......................................... 243 mm
Net weight .............................................. 2.1 kg
Rated voltage ......................................... D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
4
Explanation of general view
10 Switch trigger
11 Reversing switch lever
12 A side
13 B side
14 Clockwise
15 Counterclockwise
16 Low speed
17 High speed
6216D 6236D
10 mm
36 mm
6 x 75 mm
6 mm
0 – 1,300
0 – 400
243 mm
2.2 kg
D.C. 14.4 V
9.
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
12. The battery charger is not intended for use by
ENC001-3
13. Young children should be supervised to ensure
14. If operating time has become excessively
15. If electrolyte gets into your eyes, rinse them out
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1.
2.
3.
4.
18 Speed change lever
19 Adjusting ring
20 Graduations
21 Drill marking
22 Pointer
23 Limit mark
24 Brush holder cap
25 Screwdriver
6316D
13 mm
30 mm
6 x 75 mm
6 mm
0 – 1,300
0 – 400
255 mm
2.2 kg
D.C. 12 V
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not charge Battery Cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6336D
13 mm
36 mm
6 x 75 mm
6 mm
0 – 1,300
0 – 400
255 mm
2.3 kg
D.C. 14.4 V