Stroller Operation - Joie chrome Bedienungsanleitung

Assemble Armbar
Align the armbar ends with the armbar mounts, and then insert to lock.
To disassemble armbar, press armbar release button
Assemble Hood
To assemble hood, insert clips into mount , then attach 2 pairs of buttons.
The completely assembled stroller is shown as 11

Stroller Operation

Use Hood
Open the zipper, then push the Hood forwards to open the Hood.
To fold the hood, pull hood toward back.
To remove hood, detach clips from mount while pressing the fixing tab
to attach the hood fabric to the seat) now lift of the hood.
!
Once fitted, removing the hood on a regular basis is not recommended.
Switch Seat
The seat can be switched, which makes mother and child can face to face with each.
Squeeze the seat release buttons while lifting the seat.
seat to seat mounts. 16
Adjust Recline
There are 5 positions for the backrest.
To recline the backrest, squeeze the adjustment button
- 2
17
To raise the backrest, push up.
!
Make sure the recline is set properly for use.
Use Buckle
Release Buckle
18
Press the center button to release the buckle.
Lock Buckle
Match the waist belt buckle with the shoulder buckle
A "click" sound means the buckle is locked completely.
!
To avoid serious injury from falling or sliding out, always secure your child with harness.
!
Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
! Do not cross the shoulder belts. This will cause pressure on child's neck.
15
9
- 1 - 2
10 , and then pull out the armbar. 10
14
12
13 , then detach 2 pairs of buttons (used
14
15
Turn the seat to reverse direction, and then insert the
- 1
17 , and then adjust the backrest to a desired angle.
- 1 - 2
19 , and click into the center buckle. 19
- 3
19
Use Shoulder & Waist Harnesses
!
In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
- 1
20 Shoulder harness anchor A
20 - 2
Shoulder harness anchor B
- 3
20
Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder
harness anchor B and the lowest shoulder slots.
To adjust the position of the shoulder harness anchor, turn the anchor to be level with the side facing forward.
Thread it through the shoulder harness slot from back to front.
22
child's shoulder height.
Use slide adjuster to change the harness length. 23
- 2
Press the button 23 , while pulling the waist harness to proper length.
Use Crotch Harness
There are 2 positions the crotch strap can be adjusted to according to the requirements of the child.
- 1
24
Position 1 Smaller babies use this position
- 2
Position 2 Larger babies use this position 24
i. Pull the crotch harness out and place it to be level.
ii. Rotate the crotch harness anchor to make the short side forwards, then thread it through the crotch harness
- 3 - 4
slot. 25 & 25
iii. Rethread it through the slot that is closest to child's crotch from the front of the crotch harness.
Adjust Calf Support
The calf support has 2 positions.
Raise Calf Support
To raise the calf support, just push it upwards.
Lower Calf Support
Press the adjustment buttons on both sides of the calf support
26 - 2
Use Front Swivel Lock
Push up the front swivel locks to maintain the moving direction.
Tip It is recommended to use swivel locks on uneven surfaces.
Use Brake
28
To lock wheels, step the brake lever downwards.
To release wheels, just lift the brake lever upwards.
Tip Always apply brake when stroller is in stopped position.
21 Rethread it through the slot that is closest to
- 1
- 3
23
- 1 - 2
25 & 25
24
- 1
26 , and rotate the calf support downwards.
27
29
16