Additional Requirements; Environmental Protection; Packaging; Door Disassembly - Wisniowski SSp Montage- Und Bedienungsanleitung

EN
To tighten the springs, steel rods are applied, which ends should conform to the
holes in spring drums. The person who tightens the springs should be correspond-
ingly trained, and no other people should stay in the vicinity. When tightening,
the person who tightens should stand on scaffoldings next to the spring to en-
sure that the tightening rods and springs are not located in front of him or her.
Before starting the proper tightening, check if the springs are securely fixed on
drums, and if springs do not have visible cracks and deformations. Then loosen
the screws fastening spring drum with shaft. The tightening should be performed
by ¼ revolutions till the required tension is achieved. During tightening, insert one
rod into the spring drum hole, and turn it to such an angle as to enable the second
rod to be inserted in the next spring drum hole. When the second rod is securely
fixed in the drum hole, remove the first rod, but continue to hold firm the second
rod. Repeat the procedure till the required tension is achieved. During tightening,
the spring will stretch and decrease its diameter. When the desired tension is
achieved, carefully tighten the screws fastening spring drum with shaft. Then, re-
move the the tightening rods. Repeat the procedure to tighten the second spring.
This Instruction provides exemplary number of spring turns. The actual num-
ber of spring turns may differ slightly from the number of turns stated on the
manufacturer's plate of the door. This is explained by specific conditions of the
particular door installation.
When the door installation is completed, check whether the door operates
according to the Assembly and Operating Instruction. If necessary, make cor-
responding adjustments.
Check the correct tension of springs, and, if necessary, adjust it. To do this:
• open the door by lifting its leaf to half-open position,
• if the leaf is visibly falling, increase the spring tension by its regulation,
• if the leaf is visibly lifting, decrease the spring tension by its regulation.
[B000094] If the above mentioned works are not per-
formed, there is a risk that the leaf may suddenly fall
down and hurt people, or cause damage to objects in its
vicinity.
[A000007] 8. ADDITIONAL REQUIREMENTS
After the installation is completed, it must be checked that the door is fitted with
CE data plate according to the standard. If this plate is missing, fit the door with
such a data plate. After verifying the correct operation of the door, the Assembly
and Operating Instruction and door report book, if required, should be handed
over to the Owner.
[A000015] Activities, which may be performed by the Owner after careful
reading of the Assembly and Operating Instruction supplied with the door.
When the door is installed, the protective foil should be
immediately removed from the door leaf.Failure to do
so will result in a strong adherence of the foil to the door
skin metal under the influence of temperature and sun
rays. This will make it impossible to remove the foil and
may lead to coating deterioration.
[A000008] 9. ENVIRONMENTAL PROTECTION

Packaging

Elements of packaging (cardboard, plastics, etc.) are classified as waste suit-
able for recycling. Follow local legislation for specific material before throw-
ing it away.
Scrapping
The product consists of many different materials. Most of the materials used are
suitable for recycling. Sort it before disposal, and then deliver to refuse collec-
tion and disposal area for recycling.
Follow local legislation for specific material before
scrapping.
[A000009] Remember! Recycling of packaging materials
saves natural resources and reduces the amount of
wastes.
[C000022] 10. DOOR DISASSEMBLY
• Close and lock the door.
• Release the tension of door springs.
• Perform the assembly procedure in the reverse order.
[A000029] 11. OPERATING AND MAINTENANCE INSTRUCTION
The Assembly and Operating Instruction is a documentation intended for the
door owner.
Please read carefully this instruction and follow its recommendations. The
instruction includes information ensuring safe usage, operation and mainte-
nance of the door.
4
Assembly and Operating Instructions – Sectional garage door UniTherm
[A000010] 12. IMPORTANT INFORMATION AND NOTES
• Please carefully keep this instruction.
• All operating activities must be performed according to the door
Assembly and Operating Instruction.
• Occupational health and safety regulations and recommenda-
tions included in the Assembly and Operating Instruction must
be observed during all works related to the door inspections
and repairs.
• It is prohibited to change any door components or parts.
[B000006] 13. INFORMATION REGARDING FORBIDDEN DOOR
USAGE
• It is forbidden to open the door if the guides are not mounted.
• It is forbidden to obstruct the door movement area. When operat-
ing the door, make sure there are no people, especially children,
or objects within the door movement area.
• It is forbidden for people to stay, or leave cars or other objects in
a clearance of the opened door.
• It is prohibited to stay, walk, run or drive under the moving door.
• It is prohibited to use the door leaf to lift objects or people.
• Do not allow children to play with equipment. Transmitters for
door operation must be kept away from children. Transmitters
should be kept in dry, moisture-free places.
• It is forbidden to modify or remove any door components! This
may cause damage to parts ensuring the door safe usage.
• [B000010] It is forbidden to install any additional fillings or
thermal insulation in the door leaf without a written consent of
"WIŚNIOWSKI" Sp. z o.o. S.K.A. Springs are precisely adjusted
to the door leaf weight, and all additionally mounted elements
may cause its overload and incorrect door operation.
• [B000093] Doors with electric drive must be opened according
to drive Assembly and Operating Instruction.
• [B000008] The door should be protected against harmful agents
(including corrosive agents, like acids, alkali, salts), which may
damage the paint coating and metal. The door should also be
protected against plaster, paints and solvents which may cause
stains, during finishing or repairing the room.
[C000011] 14. DOOR OPERATING INSTRUCTION
• It is prohibited to obstruct the door movement area.
The door opens vertically upwards. Therefore, no obstacles may
be located in the way of door opening or closing. It is necessary
to ensure that during door movement no persons, especially chil-
dren, or objects are on its way.
Caution! Risk of accident.
• [A000053] It is prohibited to keep using the defective door. It is
particularly forbidden to operate the door, if there is any visible
damage of counterbalancing springs, mounting elements or any
other parts responsible for safe door operation.
• [A000062] Any self-retained repairs of the door are prohib-
ited.
• [B000103] IMPORTANT! Damage due to temperature
difference.
Difference between external (ambient) temperature and internal
(premises) temperature may lead to deformation of the door ele-
ments (bimetallic effect). In this case door operation may result
in its damage.
• [B000007] It is prohibited to keep using the door, if any faults in
its operation, or damage of its components are found. In this case,
immediately put the door out of service, and contact the author-
ized service centre.
[C000012] Check the proper mounting of the door according to As-
sembly and Operating Instruction before its first opening.
The door is mounted properly when its leaf/curtain moves smoothly and its op-
eration is easy.
[B000104] Manually-operated garage doors should be opened and closed
smoothly, without sharp jerks that negatively influence its durability and safe
operation.
[C000399] Opening - the door should be operated manually, using the rel-
evant outside or inside handles/ pulls. Improper operation of the door may
cause accident.
Closing - the door should be closed manually by pushing it vigorously using the
handle. As a result, the door self-locking bolts will latch on proper door frame
elements.
IIiO/BS/UniTherm/07/2015/ID-95145 Technical description
+