Using The Saw; Operation - EINHELL 43.071.53 Bedienungsanleitung

Anleitung_RT_TS_2031_U_SPK1:_

8.0. Using the saw

8.1. ON/OFF switch (Fig. 1/11)
To turn the saw on, press the green button "I" .
Wait for the blade to reach its maximum speed
of rotation before commencing with the cut.
To turn the machine off again, press the red
button "0".
8.2. Cutting depth (Fig. 35)
Turn the hand crank (8) to set the blade (4) to
the required cutting depth.
Turn anti-clockwise:
Turn clockwise:
8.3. Parallel stop
8.3.1. Stop height (Figure 26/27)
The parallel stop (7) supplied with the bench-
type circular saw has two different guide faces.
For thick material you must use the stop rail (20)
as shown in Fig. 26, for thin material you must
use the stop rail as shown in Fig. 27.
8.3.2 Cutting width (Fig. 26/27)
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpieces.
The parallel stop (7) should be mounted on the
right-hand side of the saw blade (4).
The parallel stop (7) must be pushed into the
guide (17) from the outside.
Set the parallel stop (7) to the required
dimension and fix it in place with the eccentric
lever (9).
8.3.3. Setting the stop length (Fig. 27)
The stop rail (37) can be moved in longitudinal
direction in order to prevent the workpiece from
becoming jammed.
Rule of thumb: The rear end of the stop comes
up against an imaginary line that begins roughly
at the center of the blade and runs at an angle of
45° to the rear.
Set the required cutting width:
- Slacken the thumb screws (38) and push the
stop rail (37) forward until it touches the
imaginary 45° line.
- Re-tighten the thumb screws (38).
11.03.2009 14:39 Uhr
8.4. Cross stop (Figure 28)
Slide the universal stop (7) into the guide rail
(39).
Slacken the clamping screw (12).
Turn the universal stop (7) until the arrow points
to the angle required.
Retighten the clamping screw (12).
Important!!
Do not push the stop rail (37) too far toward the
blade.
The distance between the stop rail (37) and the
blade (4) should be approx. 2 cm.
larger cutting depth
8.5. Setting the angle (Fig. 25)
smaller cutting depth
Loosen the star grip screws (a).
Set the chip box (17) to the left to the desired
angle.
Retighten the star grip screws (a).

9.0. Operation

Important!!
After every new adjustment we recommend you
to make a trial cut in order to check the new
settings.
After switching on the saw, wait for the blade to
reach its maximum speed of rotation before
commencing with the cut.
Take extra care when starting the cut!
9.1. Making longitudinal cuts (Figure 29)
Longitudinal cutting (also known as slitting) is when
you use the saw to cut along the grain of the wood.
Press one edge of the workpiece against the parallel
stop (7) while the flat side lies on the saw table (1).
The guard hood (2) must always be lowered over the
workpiece.
When you make a longitudinal cut, never adopt a
working position that is in line with the cutting
direction.
Set the parallel stop (7) in accordance with the
workpiece height and the desired width. (See
8.3.)
Switch on the saw.
Place your hands (with fingers closed) flat on the
workpiece and push the workpiece along the
parallel stop (7) and into the blade (4).
Guide at the side with your left or right hand
(depending on the position of the parallel stop)
only as far as the front edge of the guard hood.
Always push the workpiece through to the end of
the splitter (5).
The offcut piece remains on the saw table (1)
until the blade (4) is back in its position of rest.
Seite 19
GB
19