Using The Saw - EINHELL TC-TS 254 eco Originalbetriebsanleitung

blade guard (2) (see 6.4).
•
Undo the screw (15) with a wrench (38) on
the screw (15) itself and a second wrench
(39) on the motor shaft to apply counter-
pressure.
•
Caution! Turn the screw (15) in the direction
of rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade (4) off the inner flange.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Fit and fasten the new saw blade (4) in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter (5) and the saw blade
guard (2) (see 6.4.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the
saw blade, check that the saw blade guard
(2) opens and closes again in accordance
with requirements. Also check that the saw
blade (4) spins freely in the saw blade guard
(2).
•
Warning! Every time that you change the
saw blade (4), check to see that it spins freely
in the table insert (6) in both perpendicular
and 45° angle settings.
•
Warning! You should replace the table insert
(6) immediately whenever it is worn or dama-
ged (see 6.3).
•
Warning! The work to change and align the
saw blade (4) must be carried out correctly.
6.6 Putting away loose parts (Fig. 15)
•
When not in use, the parallel stop (7) and
push stick (3) can be secured as shown in
Fig. 15a.
•
The two wrenches (38+39) can be secured
as shown in Fig. 15b.
•
The cross stop (14) can be secured as shown
in Fig. 15c.
6.7 Connection for dust extractor (Fig. 2, 26)
A connection for a dust extractor is provided on
the extractor adapter on the housing (16) and on
the saw blade guard (2).
Anl_TC_TS_254_ECO_SPK13.indb 27
GB
6.7.1 Dust extraction using a wet & dry vac
(Fig. 2):
•
A wet & dry vac is not supplied with the pro-
duct and is available as an accessory.
•
Connect the wet & dry vac to the extractor
adapter on the housing (16).
6.7.2 Dust extraction using a vacuum ext-
raction system and extractor adapter set
(Fig. 26):
•
The product is not supplied with an extractor
adapter set with suction hose (a) and adapter
(b) or a vacuum extraction system, which are
available as accessories.
•
Using a crosstip screwdriver, undo the screw
on the cap (36) on the saw blade guard (2).
•
The the cap (36) from the saw blade guard
(2).
•
Connect the adapter (b) to the extractor ad-
apter on the housing (16).
•
Connect the saw blade guard (2) and the ad-
apter (b) to the suction hose (a).
•
A vacuum extraction system can now be
connected to the 100 mm diameter of the
adapter (b).

7. Using the saw

7.1 ON/OFF switch (Fig. 1, 16 / Item 11)
•
To turn the saw on, press the green button
„I". Wait for the blade to reach its maximum
speed of rotation before commencing with
the cut.
•
To turn the equipment off again, press the red
button „0".
7.2 Cutting depth (Fig. 1, 16)
Turn the crank (10) to set the blade (4) to the re-
quired cutting depth.
Turn anti-clockwise:
smaller cutting depth
Turn clockwise:
larger cutting depth
7.3 Parallel stop
The parallel stop (7) has to be used when making
longitudinal cuts in wooden workpieces.
- 27 -
01.09.2022 15:49:48