EINHELL 43.071.53 Bedienungsanleitung Seite 18

Anleitung_RT_TS_2031_U_SPK1:_
GB
screws (18) in each case (Figure 15).
Important: The handles (16) must be able to
move freely and must retract independently. (Fig.
15).
Attach the 2 thumb screws (27) for the terminal
strip to the front side of the saw table.
Important: Attach the thumb screws only
loosely, as otherwise it will be impossible to
mount the parallel stop (7). Mount the tool hooks
(9) on the side of a front leg. (Fig. 15).
Align the base frame and tighten all the screws.
Remove the transport brace (Figure 16).
7.2 Installing the table length extension (Figures
17-18)
Screw the short side of the length extension
table (10) loosely to the rear side of the saw
table (1) with 2 screws. (Fig. 17).
Now tightly screw the long table supports (29) to
the base frame and the length extension table
using the holes provided.
Align the length extension table (10) with the saw
table (1) so that it is flat and tighten all the
screws.
7.3 Using the chassis (Fig. 19)
To swing the chassis out, lift the saw at the back
(a) and push the wheels backwards (15) (b).
Then lower the saw again, keeping it in this
same position (c).
The saw is now standing on the wheels and can
be transported by one person with the aid of the
handles (16).
Important: After transportation, the chassis (15)
must immediately be retracted in order to ensure
that the saw is standing securely. To do this,
return the wheels to their starting position by
following the sequence in reverse.
7.4 Fitting / removing the saw blade guard (Fig.
10/20)
Mount the saw blade guard (2) on the splitter (5)
so that the screw (31) fits through the hole (30)
in the splitter.
Do not tighten the screw (31) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (14) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (14).
To remove the saw blade guard, proceed in
reverse order (Fig. 10).
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
18
11.03.2009 14:38 Uhr Seite 18
7.5 Changing the table insert (Figure 21)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2) (see 7.4).
Remove the countersunk head screws (33).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.
7.6. Setting the splitter (Fig. 20/21/22)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place (see. 8.2.
Remove the saw blade guard (see 7.4).
Take out the table insert (6) (see 7.5).
Slacken the nut (32).
7.6.1 Setting for maximum cuts (Figures
20/21/22/23)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) is at its maximum.
The maximum distance between the saw blade
(4) and the splitter (5) is 8 mm.
Re-tighten the nut (32) and mount the table
insert (6).
7.7. Changing the saw blade (Abb. 24)
Important. Pull out the power plug.
Set the saw blade (4) to max. cutting depth (see
8.2)
Take off the saw blade guard (2) (see 7.4).
Take out the table insert (6) (see 7.5).
Place the counterholder (35) on the saw blade
flange.
Using the wrench (34), turn out the screw (26) in
the running direction of the saw blade.
Remove the saw blade (4) from the inner flange
and pull out in an upwards direction.
Clean the blade flange thoroughly before fitting
the new blade.
Mount and fasten the new saw blade in reverse
order.
Important. Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the arrow
on the blade guard).
Refit and set the splitter (5) and the saw blade
guard (2) (see 7.4., 7.5.)
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.