Seite 1
5 3 3 5 2 - D r a h t M e s s u m f o r m e r m i t H A R T ® P r o t o k o l l N r .
Seite 2
PR electronics A/S tilbyder et bredt program af analoge og digitale signalbehandlingsmoduler til industriel automation. Programmet består af Isolatorer, Displays, Ex-barrierer, Temperaturtransmittere, Universaltransmittere mfl. Vi har modulerne, du kan stole på i selv barske miljøer med elektrisk støj, vibrationer og temperaturudsving, og alle produkter opfylder de strengeste internationale standarder.
2-DRAHT MESSUMFORMER ® MIT HART PROTOKOLL 5335 • Eingang für WTH, TE, Ω oder mV • Extreme Messgenauigkeit ® • HART Kommunikation • Galvanische Trennung • Für Einbau in Anschlusskopf DIN Form B Verwendung • Linearisierte Temperaturmessung mit Pt100...Pt1000, Ni100...Ni1000 oder Thermoelementsensor.
ANWENDUNGEN 2-Draht-Installation WTH in 4...20 mA im Kontrollraum 2-Draht-Installation TE en 4...20 mA im Kontrollraum Widerstand 2-Draht-Installation im Kontrollraum in 4...20 mA 2-Draht-Installation mV in 4...20 mA im Kontrollraum Di erenz oder Mittel 2-Draht-Installation im Kontrollraum WTH, TE oder mV 5 33 5 V 1 16 - DE...
Bestellangaben: 5335 Version 5335 Standard CSA, FM, ATEX, IECEx & INMETRO Zübehör 5909 = Loop Link USB Schnittstelle und PReset Software 8421 = Montagebügel für Kopfmessumformer Elektrische Daten Spezifikationsbereich: -40°C bis +85°C Gemeinsame Daten: Versorgungsspannung, DC Standard ............. 8,0...35 V CSA, FM, ATEX, IECEx &...
Seite 7
Grundwerte Grund- Temperatur- Eingangsart Genauigkeit koeffizient ≤ ±0,1°C ≤ ±0,005°C/°C Pt100 & Pt1000 Ni100 ≤ ±0,2°C ≤ ±0,005°C/°C ≤ ±0,1 Ω ≤ ±5 mΩ / °C Lin. R Volt ≤ ±10 µV ≤ ±0,5 µV / °C TE-Typ: ≤ ±0,5°C ≤...
Seite 8
Elektrische Daten, Eingang: Max. Nullpunktverschiebung (Offset) ..... 50% des gew. num. Max.-Wertes WTH- und Linearer Widerstandseingang: WTH- Min. Max. Min. Wert Wert Spanne Norm Pt100 -200°C +850°C 10°C IEC 60751 Ni100 -60°C +250°C 10°C DIN 43760 Lin. R 0 Ω 7000 Ω...
Seite 9
EAC TR-CU 020/2011 ..........EN 61326-1 Marine-Zulassung: Det Norske Veritas, Ships & Offshore ..... Stand. for Certific. No. 2.4 I.S. / Ex: 5335A: ATEX 94/9/EG ..........KEMA 03ATEX1508 X IECEx ..............KEM 10.0083 X 5335D: ATEX 94/9/EG ..........KEMA 03ATEX1537 IECEx ..............
PROGRAMMIERUNG 5335 kann in 3 verschiedener Weise programmiert werden: 1. Mittels PR electronics A/S’ Kommunikationsschnittstelle Loop Link und PReset PC Programmierungssoftware. 2. Mittels HART ® Modem und PReset PC Programmierungssoftware. 3. Mittels HART ® Datenaustauschgerät mit PR electronics A/S’ DDL-Antrieb.
Bezüglich Programmierung verweisen wir auf die nachfolgende Zeichnung. Um Zu tritt zur Produktspezifischen Kommandos zu bekommen, muss das HART ® Daten-aus tauschgerät mit dem DDL-Antrieb von PR electronics A/S ausgestat- tet sein. Der Antrieb ist von HART ® Commu nica tion Foundation oder PR electro- nics A/S erhältlich.
PARALLELANSCHLUSS VON SIGNALGEBERN (MULTIDROP) ® Ein HART Datenaustauschgerät oder ein PC-Modem kann über die Punkte AB oder BC angeschlossen werden. PRetop PRetop PRetop 5335 5335 5335 Spannungs- versorgung Max. 15 Signalgeber > 250 Ω, < 1100 Ω Belastung Im Ausgang können bis zu 15 Signalgeber für eine digitale Kommunikation über Zweileiter parallel geschaltet werden.
WWW.PRELECTRONICS.COM ATEX Installationszeichnung 5335QA02 Für die sichere Installation von 5335A oder 5337A ist Folgendes zu beachten: Das Gerät darf nur von qualifiziertem Personal eingebaut werden, das mit den nationalen und internationalen Gesetzen, Richtlinien und Standards auf diesem Gebiet vertraut ist.
Seite 17
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM Wenn der Messumformer mit einem funkenfreien Signal von Typ „nA“ versorgt ist oder mit einem funkenfreien Signal in Verbindung ist, muss der Messumformer in einem Metallkopf Form B gemäß DIN 43729 montiert werden. Das Gehäuse muss einen Schutzgrad von mindestens IP 6X gemäß...
Seite 18
WWW.PRELECTRONICS.COM IECEx Installation drawing 5335QI02 For safe installation of 5335A or 5337A the following must be observed. The module shall only be installed by qualified personnel who are familiar with the national and international laws, directives and standards that apply to this area.
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM ATEX Installationszeichnung 5335QA01 Für die sichere Installation von 5335D oder 5337D ist Folgendes zu beachten: Das Gerät darf nur von qualifiziertem Personal eingebaut werden, das mit den nationalen und internationalen Gesetzen, Richtlinien und Standards auf diesem Gebiet vertraut ist. Das Baujahr kann aus den ersten beiden Ziffern der Seriennummer ersehen werden.
Seite 20
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM Installationsvorschriften Allgemeine Installationsvorschriften: Die galvanische Trennung zwischen dem Sensorkreis und dem Versorgungs-Ausgangskreis ist nicht unfehlbar. Allerdings ist die galvanische Trennung zwischen den Kreisen so ausgelegt, dass diese eine Testspannung von 500 VAC für eine Minute aushält. Wenn das Gehäuse aus Aluminium ist, ist das Gehäuse so zu montieren, dass Zündquellen (Stöße und Reibungsfunken) selbst bei selten auftretenden Störungen vermieden werden.
Seite 21
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM IECEx Installation drawing 5335QI01 For safe installation of 5335D or 5337D the following must be observed. The module shall only be installed by qualified personnel who are familiar with the national and international laws, directives and standards that apply to this area.
Seite 22
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM Installation notes. General installation instructions The sensor circuit is not infallibly galvanic isolated from the supply output circuit. However, the galvanic isolation between the circuits is capable of withstanding a test voltage of 500Vac during 1 minute.
Seite 23
5300QF01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM FM Installation Drawing 5300Q502 Rev AH Model 5331C,5331D, 5333C, 5333D and 5343B Non Hazardous Location Hazardous (Classified) Location Class I,Division1, Groups, A,B,C,D T4..T6 Associated Apparatus Class I, Zone 0, AEx ia IIC T4..T6 or Barrier with Ambient temperature limits entity Parameters: T4: ‐40 to + 85 deg. Celcius T6: ‐40 to + 60 deg. Celcius...
Seite 24
5300QF01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM The entity concept The Transmitter must be installed according to National Electrical Code (ANSI-NFPA 70) and shall be installed with the enclosure, mounting, and spacing segregation requirement of the ultimate application. Equipment that is FM-approved for intrinsic safety may be connected to barriers based on the ENTITY CONCEPT.
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM CSA Installation drawing 533XQC03 Hazardous area Non Hazardous Area T4: -40 ≤ Ta ≤ 85ºC T6: -40 ≤ Ta ≤ 60ºC Module 5331D, 5333D Terminal: 3,4,5,6 Only passive, or non-energy storing devices such as RTD’s and Thermocouples may be connected Barrier...
Seite 26
5335QE01 LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM Instruções de Segurança 5335QB01 5335D, 5337D: Instalação Ex: ATENÇÃO - RISCO POTENCIAL DE CARGA ELETROSTÁTICA - VER INSTRUÇÕES Para a instalação segura do transmissor 5335D, 5337D em áreas classificadas, deve-se observar o seguinte: O módulo necessita ser instalado somente por pessoal qualificado e que tenham familiaridade com normas internacionais, diretivas e normalização aplicadas à...
Seite 27
Lo ............: 35 mH Co ............: 3,5 µF 5335A, 5337A: Instalação Ex: ATENÇÃO - RISCO POTENCIAL DE CARGA ELETROSTÁTICA - VER INSTRUÇÕES Montado no interior de um invólucro metálico forma B de acordo com a norma DIN 43729 com um grau de proteção pelo menos IP-54 de acordo com a norma IEC 60529, que seja adequado para esta aplicação e...
Seite 28
Displays Programmable displays with a wide selection of inputs and outputs for display of temperature, volume and weight, etc. Feature linearization, scaling, and difference measurement functions for programming via PReset software. Ex interfaces Interfaces for analog and digital signals as well as HART signals between sensors / I/P converters / frequency ®...