Dust/Chip Extraction; Starting Operation - Bosch PMF 10,8 LI Originalbetriebsanleitung

OBJ_BUCH-1170-003.book Page 17 Friday, July 15, 2011 1:30 PM
To remove the sanding sheet 13, grasp it at one of the tips and
pull it off from the sanding plate 12.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Sanding disc Material
– All wooden materials
(e. g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
Red quality
– Paint
– Varnish
– Filling compound
– Filler
White quality

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figure A)
Remove the application tool/accessory when mounting the
dust extraction 18 (accessory).
If required, assemble the parts of the dust extraction 18 as
shown in the figure. Position the assembled dust extraction
onto the machine via the tool holder 7. Turn the dust extrac-
tion in such a manner that the cams of the dust extraction en-
gage into the corresponding recesses on the housing. Fasten
the dust extraction to the machine with the retaining clip 16
as shown in the figure.
Bosch Power Tools
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Application
For coarse-sanding, e. g. of rough, unplaned beams
and boards
For face sanding and planing small irregularities
For finish and fine sanding of wood
For sanding off paint
For sanding primer (e. g., for removing brush dash-
es, drops of paint and paint run)
For final sanding of primers before coating
Pay attention that the felt ring 15 is undamaged and faces
tightly against the sanding plate 12. Replace a damage felt
ring immediately.
Place a vacuum hose 19 (accessory) onto the vacuum con-
nection 17. Connect the vacuum hose 19 with a vacuum
cleaner (accessory). An overview for the connection of vari-
ous vacuum cleaners can be found at the end of these instruc-
tions.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation

Starting Operation

Inserting the Battery
Use only original Bosch lithium ion batteries with the
voltage listed on the nameplate of your power tool. Us-
ing other batteries can lead to injuries and pose a fire haz-
ard.
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Insert the charged battery 2 into the handle until it can be felt
to engage and faces flush against the handle.
English | 17
Grain size
coarse 40
60
medium 80
100
120
fine 180
240
320
400
coarse 40
60
medium 80
100
120
fine 180
240
320
2 609 004 157 | (15.7.11)