Dust/Chip Extraction - Bosch GWS 12-125 CIP Professional Originalbetriebsanleitung

Rotating the Machine Head (see figure A)
Pull the plug out of the socket before carrying out any
u
work on the power tool.
The machine head can be rotated in 90° increments. In this
way, the on/off switch can be brought into a more favourable
handling position for particular applications, e.g. for left-
handed tool users.
Completely unscrew the four screws. Rotate the machine
head carefully, without removing it from the housing, into
the new position. Screw in and retighten the four screws.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-Up
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
When operating the power tool using a mobile generator that
does not have sufficient reserve capacity or an adequate
voltage control system with inrush current boost converter,
loss of performance or atypical behaviour may occur upon
switch-on.
Please check the suitability of the power generator you are
using, particularly with regard to the mains voltage and fre-
quency.
Hold the tool by the insulated gripping surfaces and
u
auxiliary handle only. The application tool could come
into contact with hidden wiring or its own cord. Con-
tact with live wires may make metal parts of the tool live,
posing a risk of electric shock.
Bosch Power Tools
Switching On/Off
To start the power tool, push the unlocking lever (5) to the
rear and then push the on/off switch (3) upwards.
To switch off the power tool, release the on/off switch (3).
Always check abrasive tools before using them. The
u
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Kickback stop
(GWS 12-125 CIP / GWS 12-125 CIEP /
GWS 15-125 CIP / GWS 15-125 CIEP / GWS 15-150 CIP)
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
To restart the tool, set the On/Off switch (3) to the "off" po-
sition and then switch the power tool on again.
Restart protection
(GWS 12-125 CIP / GWS 12-125 CIEP /
GWS 15-125 CIP / GWS 15-125 CIEP / GWS 15-150 CIP)
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (3) to the "off" posi-
tion and then switch the power tool on again.
Starting current limitation
(GWS 12-125 CIP / GWS 12-125 CIEP /
GWS 15-125 CIP / GWS 15-125 CIEP / GWS 15-150 CIP)
The electronic starting current limitation feature restricts the
power of the power tool when it is switched on and enables
operation using a 16 A fuse.
Note: If the power tool runs at full speed immediately after
being switched on, this means that the starting current limit-
ation and restarting protection mechanisms have failed. The
power tool must be sent to the after-sales service immedi-
ately; see the "After-Sales Service and Application Service"
section for addresses.
Constant Electronic control
(GWS 12-125 CIP / GWS 12-125 CIEP /
GWS 15-125 CIP / GWS 15-125 CIEP / GWS 15-150 CIP)
The Constant Electronic keeps the speed at no load and un-
der load virtually consistent, guaranteeing uniform perform-
ance.
English | 25
1 609 92A 6PP | (23.06.2021)