Bosch PMF 10,8 LI Originalbetriebsanleitung Seite 16

OBJ_BUCH-1170-003.book Page 16 Friday, July 15, 2011 1:30 PM
16 | English
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-
sories program.
Accessory
BIM segment saw
blade
Base plate for sand-
ing, series Delta
93 mm
HCS plunge cut saw
blade, wood
HCS plunge cut saw
blades, wood
BIM plunge cut saw
blades, metal
HM-Riff segment
saw blade
HM-Riff delta plate Mortar, concrete remain-
Scraper, rigid
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/
accessory.
For removing the application tool/accessory loosen the screw
10 with the allen key 11 and remove the tool.
Mount the application tool/accessory (e.g. plunge cut saw
blade 9) in such a way on the tool holder 7 that the openings
of the tool engage into the cams of the tool holder.
For a safe and fatigue-free working position it is possible to
position the application tools/accessories in any snap-in posi-
tions on the tool holder. Position the tool in such a way that
the depressed centre points downwards (marking on the tool
is readable from above, see figure on the graphics page).
Use the screw 10 to fasten the application tool/accessory.
Tightly fasten the screw 10 with the allen key 11.
2 609 004 157 | (15.7.11)
Material Application
Wooden materials, plas- Separating and plunge cuts; also for sawing close to edges,
tic, non-ferrous metals in corners and hard to reach areas;
example: shortening already installed bottom rails or door
hinges, plunge cuts for adjusting floor panels
Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach
areas;
depending on the sanding sheet for, e.g., sanding wood,
paint, varnish, stone
Wooden materials, soft Separating and deep plunge cuts; also for sawing close to
plastics edges, in corners and hard to reach areas;
example: narrow plunge cut in solid wood for installing a
ventilation grid
Wooden materials, soft Smaller separating and plunge cuts;
plastics example: cut-outs in furniture for cable connections
Metal (e. g. unhardened Smaller separating and plunge cuts;
nails, screws, smaller pro- example: shortening narrow profiles, cutting fastening
files), non-ferrous metals elements such as staples
Grouting joints, soft wall Cutting and separating close to edges, in corners or hard to
tiles, glass-fibre reinforces reach areas;
plastic and other abrasive example: removing grouting joints between wall tiles for
materials repair work, cutting openings in tiles, gypsum boards or
plastic
Rasping and sanding on hard surfaces;
ders, wood, abrasive ma- example: removing mortar or tile adhesive (e.g. when
terials replacing damaged tiles)
Carpets, coverings Scraping on hard surfaces;
example: removing carpet and tile adhesive
Check the tight seating of the application tool/
accessory. Incorrect or not securely fastened application
tools/accessories can come loose during operation and
pose a hazard.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 12 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 13, free the Velcro back-
ing of the sanding plate 12 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 13 flush alongside one edge of the
sanding plate 12, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Bosch Power Tools