Specifications; Screwdriver Safety Warnings; Functional Description - Makita 6827 Betriebsanleitung

ENGLISH
(Original instructions)
1 Pointer
2 Locator
3 Front cap

SPECIFICATIONS

Model
Capacities
Self drilling screw .................................................6 mm
Machine screw .....................................................8 mm
Wood screw .......................................................6.2 mm
–1
No load speed (min ) ...................................... 0 – 2,500
Overall length ..................................................... 304 mm
Net weight ............................................................. 1.8 kg
Safety class ............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

SCREWDRIVER SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces,
when performing an operation where the fas-
tener may contact hidden wiring or its own cord.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
4
Explanation of general view
4 Adjusting ring
5 Switch trigger
6 Lock button
SAVE THESE INSTRUCTIONS.
6827
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

/II
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Depth adjustment (Fig. 1, 2 & 3)
When you wish to drive self drilling screws, etc., adjust
the depth as follows. Turn the locator to adjust the depth.
Initially, adjust the locator to create a distance of approxi-
mately 1 mm from the tip of the front cap (which works in
conjunction with the locator) to the base of the screw
head. One full turn of the locator equals 1 mm change in
depth.
After adjusting the locator, turn the adjusting ring so that
the 6" mark is aligned with the pointer on the gear hous-
ing. Drive a trial screw into your material or a piece of
duplicate material. If the depth is not suitable for the
GEA010-1
screw, continue adjusting until the proper depth setting is
obtained.
Switch action (Fig. 4)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
GEB017-4
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
NOTE:
• Even with the switch on and motor running, the bit will
not rotate until you fit the point of the bit in the screw
head and apply forward pressure to engage the clutch.
Reversing switch action (Fig. 5)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of
rotation.
the
position (B side) for counterclockwise rotation.
E
7 Reversing switch lever
8 Hook
Move the reversing
position (A side) for clockwise rotation or the
D
switch lever to