Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GKS 160 Professional Originalbetriebsanleitung

OBJ_BUCH-185-005.book Page 19 Wednesday, March 5, 2014 9:54 AM
Sawing with Auxiliary Guide (see figure E)
For sawing large workpieces or straight edges, a board or strip
can clamped to the workpiece as an auxiliary guide; the base
plate of the circular saw can be guided alongside the auxiliary
guide.
Sawing with Guide Rail (see figures G–H)
The guide rail 30 is used to carry out straight cuts.
The adhesive coating prevents the guide rail from slipping and
protects the surface of the workpiece. The coating of the
guide rail allows the circular saw to glide easily.
The rubber lip on the guide rail acts as a splinter guard; it pre-
vents fraying of the surface while sawing wooden materials.
For this, the teeth of the saw blade must face directly against
the rubber lip.
The guide-rail adapter 29 is required for working with the
guide rail 30. The guide-rail adapter 29 is mounted in the
same manner as the parallel guide 11.
The following work steps are required for exact cuts using the
guide rail 30:
– Place the guide rail 30 on to the workpiece projecting light-
ly over the side. Pay attention that the side with the rubber
lip faces to the workpiece.
2
1
– Set the circular saw with the premounted guide-rail adapt-
er 29 on to the guide rail 30.
– Adjust the desired cutting depth and the bevel angle. Ob-
serve the marks on the guide-rail adapter 29 for preadjust-
ment of the various bevel angles; see figure G.
– Align the circular saw with guide-rail adapter in such a man-
ner that the teeth of the saw blade 21 face against the rub-
ber lip. The position of the saw blade 21 depends on the
selected cutting angle. Do not saw into the guide rail.
0
– Tighten wing bolt 8 to lock the position of the guide-rail
adapter.
– Remove the circular saw with the premounted guide-rail
adapter 29 from the guide rail 30.
Bosch Power Tools
– Align the guide rail 30 on the workpiece in such a manner
that the rubber lip lies exactly alongside the cutting edge.
– The guide rail 30 must not extend beyond the face side
of the workpiece where the cut is to be started.
– Fasten the guide rail 30 with suitable clamping devices, e.g.,
screw clamps, on the workpiece. Set the circular saw with
the premounted guide-rail adapter 29 on to the guide rail.
– Switch the machine on and guide it in the cutting direction
applying moderate and steady feed.
Two guide rails can be connected to one with use of the con-
nection piece 31. Clamping is carried out with the four screws
located in the connection piece.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
3
around the retracting blade guard clean. Remove dust and
chips by blowing out with compressed air or with a brush.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
1-45 Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
English | 19
2 609 932 923 | (5.3.14)