Menu-Setting Of The Lokmaus - Roco Lokmaus 2 Handbuch

equip locos of other brands with ROCO decoders. Conditions are enough space to install the decoder. If
you want to install the decoder with load regulation then the loco must be equipped with a DC-motor
or the AC-motor must be converted from electrical field magnets to a motor with permanent magnets.
T -
HE MENU SETTING OF THE
The menu system of the Lokmaus 2
it to the specifications of your layout and your wishes. For example you can protect the system from
unintentional programming and emergency-stop. In order to enter the menu system you must unplug
the Lokmaus 2 while the amplifier is running, keep the button 'P' pushed meanwhile you re-plug the
®
Lokmaus 2 . The display shows you the first menu 'C0'. Using the buttons 'up' and 'down' you can also
®
select other menus e.g. 'C3'. Push 'P' again and the display shows the actual value of 'C3'. By the but-
tons 'up' and 'down' you can change this value of 'C3' and pushing 'P' you confirm and activate your
input. Pushing 'STOP' you quit this menu.
The following list tells you the various menus and explains the system-functions that you define by
those menus:
C0 – the device address of the individual Lokmaus 2
Lokmaus 2 selects it automatically. But if you have deactivated this feature by the menu CA then you
®
have to do it yourself (e.g. in case of difficulties). Addresses are valid from 01 to 30. Factory default is 01.
C1 – the number of smart-search-addresses defines the length of the smart search list. It should be
as long as the number of locos that are running on your layout. Making it longer slows down the data
transmission to the locos. But it is possible to run more locos than places in this list. This setting affects
all input devices, but only the setting of the 'master'-Lokmaus 2
Lokmaus 2 don't affect the system but are stored in the memory of this Lokmaus 2
®
if this Lokmaus 2 becomes master. Minimum is 1 maximum is 19 addresses, default is 5.
®
C2 – the smart-search-function can be enabled and disabled by this menu. If you select the value 00
the smart-search-function for this individual Lokmaus 2
doesn't stop at any address but runs continously.  1 enables the smart-search-function.
C3 – the protection (1) disables the standard programming mode for this individual Lokmaus 2
the changement of the speed steps mode. So it protects the system from unintentional use of those
functions e.g. by children. 00 deactivates those functions, 01 enables the standard programming and
the changement of the speed step mode.
C4 – the protection (2) disables the button 'STOP' of this individual Lokmaus 2
be used unintentionally e.g. by children. In any case after a short circuit you can release the layout with
this button. 00 disables the button and 01 enables it again.
C5 – protection (3) this menu defines the time you have to push the button 'P' continously to enter
the experts' programming mode. Setting it to 00 disables this programming mode on this individual
Lokmaus 2 and protects it against unintentional use e.g. by children. A value from 01 to 15 enables
®
the experts' programming mode and defines the time you have to push the button 'P' to enter the
programming tool.
C6 – the basic definition of the speed step mode. This setup defines the default speed step mode
for any loco. The display indicates it by horizontal bars: one bar means 14 speed steps, two bars 28 and
3 bars symbolize 128 speed steps. For every individual loco you can change this setup. An example: you
have selected 28 speed steps as default for all locos then you can set individually 128 speed steps for
the locos 04, 19 and 73 and 14 steps for the address 01 because this loco only supports this mode.
C7 – the reset-function restores the factory defaults of this individual Lokmaus 2
00. Setting it to 01 causes the reset. All menus of this Lokmaus
the factory.
C8 – the number of addressed devices defines how many devices are addressed by the 'master'-
Lokmaus 2 . Only a device that is addressed can send information to the 'master'-Lokmaus 2
®
to control a loco or in order to operate a turnout drive. Therefore you must increment the number of
L 2
®
OKMAUS
allows you to define a lot of settings of this digital system to adapt
®
®
®
. Normally the autoconfiguration feature of the
is activated. Changing C1 at a 'slave'-
®
is disabled. The search function at this device
are re-defined in the way it came from
®
www.roco.cc
and get activated
®
and
®
. So the 'STOP' can't
®
. C7 normally is
®
in order
®
GB
31