Listing Of Replacement Parts; General; Identification Of Model Version; Normal Use - WALTHER PILOT PILOT WA 30 Betriebsanleitung

Listing of Replacement Parts PILOT WA 30
PILOT WA 30
V 20 900 00 000
(350 bar)
Item Description Qty.
Gun Body Aluminium
1
Gun Body Stainless steel
2 Seal
Barrel Nipple
3
Needle Seal Packing (compl.)
4
5 Needle Packing Gland
6 Material Control Needle
7 „V"-Packing Ring
8 O-Ring
9 Piston
10 Serrated Lock Washer
11 Hexagonal Nut
12 Piston Spring
13 Spring Retaining Bush
14 Sleeve Nut
15 Sleeve Nut
16 Airless Spray Tip (to choice)
17 Seal
18 Needle Seat
19 O-Ring
20 Threaded Bush
21 O-Ring
22 Seal
23 Screw Plug
24 Quick-Release Fitting with Seal
25 Needle Seal
26 Needle
We recommend that the bold-faced replacement parts (i.e. wearing parts) are held on
stock !
PILOT WA 30
V 20 901 00 000
(Dosing valve)
Art. N° Qty. Art. N°
1 V 20 900 01 000 1 V 20 900 01 000
1 V 20 902 01 003 1 V 20 902 01 003
1 V 09 002 12 000 1 V 09 002 12 000
V 20 900 11 003 V 20 900 11 003
1 1
V 20 900 13 000 V 20 900 13 000
1 1
1 V 20 900 03 003 1 V 20 900 03 003
1 V 20 900 06 003 1 V 20 900 06 003
1 V 09 220 20 000 1 V 09 220 20 000
1 V 09 103 17 002 1 V 09 103 17 002
1 V 20 900 07 004 1 V 20 900 07 004
1 V 20 900 14 001 1 V 20 900 14 001
1 V 20 900 15 003 1 V 20 900 15 003
1 V 20 900 19 000 1 V 20 900 19 000
1 V 20 900 10 000 1 V 20 900 10 000
1 V 01 101 03 000 1 V 01 101 03 000
1 V 20 900 05 001
1
1 G 16 286 30 000
1 V 20 900 04 002
1 V 09 103 14 001
1 V 20 900 02 003
1 V 09 103 16 001
1 V 09 002 13 000 1 V 09 002 13 000
1 V 20 540 40 005 1 V 20 540 40 005
1 V 66 100 02 027 1 V 66 100 02 027
1 V 20 901 04 002
1 V 20 901 06 003
22
1

General

1.1 Identification of Model Version
Type Series: PILOT WA 30
Model: Automatic Airless Spray Gun
Model: Dosing valve
Manufacturer: WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Strasse 18-30
D-42327 Wuppertal
Germany
TEL: 0202/ 787-0
FAX: 0202/ 787-2217
1.2 Normal Use
The automatic Airless spray gun Model PILOT WA 30 (Art. No. V 20 900 00 000)
is exclusively designed for use with all Airless-sprayable material types and grades
such as, for example:
• paints and lacquers
• greases, oils and corrosion preventives
• adhesive compounds
• ceramic glazes
• acidiferous media (stainless specialty version only) and
• pickling solutions
If your specific material is not listed above, please contact WALTHER Spritz- und
Lackiersysteme GmbH, Wuppertal for further and detailed information.
Please note that sprayable material may only be applied to workpieces and/or similar
items.
The temperature of the spraying material shall never exceed 80° C.
The dosing valve (V 2090100000) is provided for the dosing of liquids. A spraying
finction does nor exist.
The term "normal use" also implies that any and all safety warnings, operational
handling details, etc., as contained in these Operating Instructions, are carefully
read, understood and duly complied with.
This equipment complies with the explosion protection requirements of Directive
94/9/EC (ATEX) for the explosion group, equipment category and temperature class
indicated on the type plate. When using the equipment, the requirements
specified in these Operating Instructions must be observed at all times.
The technical data indicated on the equipment rating plates and the specifications in
the chapter "Technical Data" must be complied with at all times and must not be
exceeded. An overloading of the equipment must be ruled out.
The equipment may be used in potentially explosive atmospheres only with the
authorisation of the relevant supervisory authority.
The relevant supervisory authority or the operator of the equipment are
responsible for determining the explosion hazard (zone classification).
Art. No. V 20 900 00 000
Art. No. V 20 901 00 000
23