Scheppach DM460T Originalanleitung Seite 10

Manufacturer
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We wish you much pleasure and success with your new
scheppach machine.
Note
In accordance with valid product liability laws, the manu-
facturer of this device shall not be responsible for dam-
age to and from this device which results from:
• Improper care.
• Noncompliance with the Operating Instructions.
• Repairs made by unauthorized persons.
• The installation and use of any parts which are not
original scheppach replacement parts.
• Improper use and application.
• Failure the electrical system as a result of noncompli-
ance with the legal and applicable electrical directives
and VDE regulations 0100, DIN 57113 / VDE 0113.
We recommend
that you read through the entire operating instructions
before putting into operation.
These operating instructions are to assist you in getting
to know your machine and utilize its proper applications.
The operating instructions contain important notes on
how you work with the machine safely, expertly, and eco-
nomically, and how you can avoid hazards, save repair
costs, reduce downtime and increase the reliability and
service life of the machine.
In addition to the safety requirements contained in these
operating instructions, you must be careful to observe
your country's applicable regulations.
The operating instructions must always be near the ma-
chine. Put them in a plastic folder to protect them from
dirt and humidity. They must be read by every operator
before beginning work and observed conscientiously.
Only persons who have been trained in the use of the
machine and have been informed of the various dangers
may work with the machine. The required minimum age
must be observed.
In addition to the safety requirements contained in these
operating instructions and your country's applicable reg-
ulations, you should observe the generally recognized
technical rules concerning the operation of woodworking
machines.
m General notes
• After unpacking, check all parts for any transport dam-
age. Inform the supplier immediately of any faults.
• Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself with
the machine by carefully reading these instructions.
• Use only original scheppach accessories, wearing or
replacement parts. You can find replacement parts at
your scheppach dealer.
• When ordering, include our item number and the type
and year of construction of the machine.
10 english
Included with delivery
Wood turning machine
Rotating tailstock centre
Jaw spanner SW 32/41
Operating instructions
Technical data
Dimensions
L x B x H mm
Bed height mm
Headstock
thread
Headstock ta-
per
Height of cent-
ers above bed
mm
Width between
centers mm
Diameter
above bed mm
Diameter be-
tween centers
mm
Length of tool
holder mm
Weight kg
Wood turning spindle with dust-proof precision grooved ball
bearing
Revolutions
650 / 1000 / 1450 / 2000 / 3000
1/min
Tailstock
Tailstock cone
Tailstock drill
hole (hollow
spindle) ø mm
Tailstock
sleeve adjust-
ment mm
Drive
220 – 240V~ / 50 Hz
Electric Motor
Input P1 kW
Output P2 kW
Revolutions
1/min
Motor protec-
tion
Undervoltage
release
Operating
mode
Noise parameters
Acoustic power level in dB
Idling L = 74.3 dB(A),
WA
Operating L = 91.7 dB(A)
WA
Acoustic pressure level in dB
Idling L = 61.3 dB(A),
pAeq
Operating L = 78.7 dB(A)
pAeq
A measuring uncertainty coefficient (K = 3 dB) ap-
plies to the emission values listed above.
Subject to technical modifications!
DM460T
Work piece table
Carrier
Independent chuck
Mandrel
Tappet
Hex driver 3/6/8
940 x 270 x 420
190
1"X8TPI
MK 2
152
457
305
240
150
34,8
MK 2
9,5
47
0,55
0,30
1400
yes
yes
S1