Electrical Connection; Cleaning, Maintenance And Ordering Spare Parts - Scheppach Plm1800 Original Bedienungsanleitung

12. Electrical Connection

The electric motor is connected in a ready-to-oper-
ate state. The connection corresponds to the relevant
VDE and DIN regulations.
The mains connection at the customer's work place
and the extension cable used must correspond to
these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that use of the product at any
freely selectable connection point is not allowed.
• Given unfavourable conditions in the power sup-
ply the product can cause the voltage to fluctuate
temporarily.
• The product is intended solely for use at connec-
tion points that
a) do not exceed a maximum permitted supply im-
pedance Z = 0,357 Ω , or
max
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consul-
tation with your electric power company if neces-
sary, that the connection point at which you wish to
operate the product meets one of the two require-
ments, a) or b), named above.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Faulty electrical connecting leads
Insulation damage often occurs at electrical connect-
ing leads.
Causes include:
• Pressure marks caused when connecting leads
are run through windows or the cracks of doors.
• Folds caused by the improper attachment of run-
ning of the connecting leads.
• Cutsresulting from the crossing of the connecting
lead.
• Insulation damages caused by the ripping out of
the connecting lead from the wall socket.
• Cracks due to the ageing of the insulation.
Faulty electrical connecting leads such as these may
not be used and are highly dangerous due to the in-
sulation damage.
Check electrical connecting leads regularly for dam-
age. Ensure that the connecting lead is not attached
to the mains supply when you are checking it.
Electrical connecting leads must correspond to the
relevant VDE and DIN regulations. Only use con-
necting leads with the code H05VV-F.
The type designation must be printed on the con-
necting lead by regulation.
 www.scheppach.com /  service@scheppach.com /  +800 4002 4002
With a single-phase a.c. motor, we recommend a C
16A or K 16A fuse for machines with a high start-up
current (from 3000 Watt)!
13. Cleaning, maintenance and
ordering spare parts
General maintenance measures
Wipe chips and dust off the machine from time to
time using a cloth. In order to extend the service life
of the tool, oil the rotary parts once monthly. Do not
oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
m WARNING! Pull out the power plug before per-
forming any maintenance, cleaning and adjusting
work.
13.1 Cleaning
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub
the device clean with a clean cloth or blow it off
with compressed air at low pressure.
• We recommend that you clean the device directly
after every use.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can
penetrate the device interior. Water penetrating an
electrical device increases the risk of an electric
shock.
• Clean the chip ejection and/or dust extraction on a
regular basis.
• Do not spray the device with water!
13.2 Maintenance
13.2.1 Machine (fig. 21 + 22)
Periodically lubricate the following parts about every
10 operating hours:
• Anti-return claws (42)
• Threaded rod for adjusting the height of the planer
(43)
• Guide columns for height adjustment (44)
Use only dry lubricant.
The feed table, discharge table, planing table, feed/
discharge rollers and anti-return claws must always
be kept free from resin. Soiled feed/discharge rollers
or anti-return claws must be cleaned. To prevent the
motor from overheating, dust that settles in the venti-
lation openings must be removed on a regular basis.
Improve the sliding capability of the table by periodi-
cally treating it with a lubricant.
GB | 29