Scheppach CUC20-BE Originalbetriebsanleitung Seite 24

9. Assembly / Before commissioning
Warning!
Always remove the mains plug before carrying out ad-
justments on the product.
m ATTENTION!
Prior to use, ensure that the product has been cor-
rectly and fully assembled.
Unpacking (Fig. 1, 2)
• Release the locking hooks (8) and remove the ma-
chine head with filter cage (3). The accessories are
located inside the stainless steel container (1). Only
the extension pipes (25) are located outside the
stainless steel container (1) in the packaging. Re-
move all of the accessories from the stainless steel
container (1).
Installation of the roller mounts (11 + 12) (Fig. 3)
1. Turn the stainless steel container (1) upside down.
(The machine head with filter cage (3) must be re-
moved.)
2. Slide the wheels (11) into the recesses provided on
the caster mounting base (13) and screw them in
place with the screws (30).
Installation of the swivel castors (12) (Fig. 3)
1. Press the two deflection rollers (12) into the holes
provided in the roller mounts (13).
Installing the machine head with filter cage (3) (Fig. 8)
1. Place the machine head with filter cage (3) on the
stainless steel container (1).
2. Secure the machine head (3) with the locking hooks
(8). When installing the machine head with filter
cage (3), ensure that the locking hooks (8) latch into
place correctly. The water channel connection (4)
must be above the vacuum connection (2).
Installing the filter (33) (Fig. 5, 6)
Never use the product without filters! Always ensure
that the filters are correctly fitted.
Installing the foam filter (33)
1. For wet vacuuming, open and remove the filter
cage (3a) by turning it anti-clockwise (Fig. 6).
2. Pull off the clipped cover cap (3b) with a screw-
driver (not included in the scope of delivery), pull
the foam filter (33) over the filter cage with safety
float valve (3c) and refit the cover cap (3b) (Fig. 5).
24 | GB
3. Now reinsert the filter cage by turning it clockwise
(Fig. 6).
To avoid tearing the foam filter (33),
• only insert a dry filter
• knock the edge of the filter over a little to insert it and
then roll it back again.
Fit the folded filter (31) and foam filter (32) (not in-
cluded in the scope of delivery)
1. Open and remove the filter cage (3a) by turning it
anti-clockwise (Fig. 6).
2. Insert the folded filter (31) or foam filter (32) and re-
place the filter cage by turning it clockwise (Fig. 6).
Installing the paper filter bag (34) (fig. 7)
It is recommended to use an additional paper filter bag
(34) when vacuuming fine, dry dirt.
1. Slide the paper filter bag (34) over the suction
opening in the stainless steel container (1).
The paper filter bag (34) is only suitable for dry
vacuuming. The paper filter bag (34) makes it eas-
ier to dispose of the dust collected.
Filling the water tank (Fig. 15)
The water tank (9) can be removed for filling or filled
directly at the product.
1. Fill the water tank (9) through the opening (17) with
clear water (max. 3 l). Pay attention to the mark-
ings on the container (10).
2. If the water tank is heavily contaminated or
stained, add a little cleaning agent, e.g. carpet and
upholstery cleaner.
Installing the water tank (Fig. 4)
1. Take the water tank (9) by the handle (18) and place
it in the openings of the caster mounting base (13).
2. Now press the water tank (9) against the detent
(1a) until it locks into place.
Installing the suction hose (Fig. 10)
1. Connect the suction hose (22) to the correspond-
ing port, depending on the desired use, on the wet
and dry vacuum cleaner.
Vacuuming (Fig. 10)
1. Connect the suction hose (22) to the suction con-
nection (2).
2. To do so, slide the end of the suction hose con-
nection (23) with the two nipples into the suction
connection (2).
www.scheppach.com