Arktic 204979 Benutzerhandbuch Seite 8

paint, aerosol cans with a flammable propellant, flammable
GB
or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must no be tilted at an angle
greater than 5° and it is necessary to wait 12h before con-
necting it to the power supply to switch it on. The same ap-
plies if the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
• Do not attempt to climb onto the appliance.
Intended use
• This appliance is intended to be used for commercial applica-
tions, for example in kitchens of restaurants, canteens, hos-
pital and in commercial enterprises such as bakeries, butch-
eries, etc., but not for continuous mass production of food.
• The appliance is designed for aging meat only. Any other use
may lead to damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig. 1 on page 3)
1. Housing
2. Glass door with handle
3. Key lock
4. Hooks
5. Shelves
6. Led stripes
7. Control panel
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig. 2 on page 3)
Symbol Mode
Press and release
Hold for 3s
Press and release
Hold for 3s
Press and release
Hold for 3s
8
Function
Program selection
Enter settings (language, pa-
rameters, values etc)
Go back one level /
Exit a function
ON-OFF switch
Decrease value /
M`ove within a menu
-
Press and release
Hold for 3s
Press and release
Hold for 3s
Press and release
Hold for 3s
LED icons
Symbol
ON: Cooling request / De-humidify system active
OFF: Compressor OFF
Blinking: Delay time active / Delay de-humidify time active
ON: Temperature setpoint reached
OFF: Cooling cycle in progress
ON: Heating function active
OFF: Heating function inactive
ON: Evaporator fan is active
Blinking: Evaporator fan delay after defrost
ON: Light is active
OFF: Light is inactive
ON: Defrost cycle is active
OFF: Defrost cycle is inactive
Blinking: Defrost delay time / Dripping time in progress
ON: De-humidify is active
OFF: Compressor is off
Blinking: Protection delay time
ON: Humidification is active
OFF: Humidification is inactive
Blinking: Humidification is in delay time
Stand-by mode to ON / ON to Stand-by mode
• Press and hold the button for 3s to switch from Stand-by
mode to ON, or from ON to Stand-by mode.
• NOTE! The display will show the "--- ---" first, and then the
appliance will enter the Stand-by mode.
Control panel lock/unlock
• Press and hold the button for 3s to unlock the control
panel. The thermostat display will light up and show temper-
ature and humidity detected inside the chamber.
• The panel will lock automatically after 30s of inactivity. The
thermostat will shift to "rest mode" and the display's illumi-
nation will decrease.
Checking the setpoint (temperature and humidity)
• Press the button - the temperature setpoint is displayed,
flashing on the right side of the display.
• Press the button again to see the humidity setpoint flash-
ing on the right side of the display.
• Wait for about 6s to return to normal view.
Increase value /
Move within a menu
-
Activate /
Deactivate the light
-
Confirm a selected value /
Access the setpoint menu
-
Explanation
-
-
-
-