Leaving The Battery In The Charger; Wall Mounting - Stanley Sfmcbl730 Originalanweisung

SFMCB10 Charger Indicators
Charging
Fully Charged
Hot/Cold Pack Delay
nOtE: The compatible charger(s) will not charge a faulty battery
pack. The charger will indicate a faulty battery pack by refusing
to light.
nOtE: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery pack
to be tested at an authorized service centre.

Leaving the Battery in the Charger

The charger and battery pack can be left connected with the LED
glowing indefinitely. The charger will keep the battery pack fresh
and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, the green
LED will flash intermittently, while the red LED will remain on
continuously, suspending charging until the battery has reached
an appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery life.

Wall Mounting

Some STANLEY chargers are designed to be wall mountable or
to sit upright on a table or work surface. If wall mounting, locate
the charger within reach of an electrical outlet, and away from
a corner or other obstructions which may impede air flow. Use
the back of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely using
drywall screws (purchased separately) at least 25.4 mm long,
with a screw head diameter of 7–9 mm, screwed into wood to
an optimal depth leaving approximately 5.5 mm of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
nOtE: Do not attempt to mount SFMCB10 charger under a
bench or table.
nOtE: Only mount SFMCB10 charger with the charging lights
pointed upward toward the ceiling.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be removed
from the exterior of the charger using a cloth or soft non-metallic
brush. Do not use water or any cleaning solutions. Never let any
liquid get inside the tool; never immerse any part of the tool into
a liquid.
Fuel Gauge Battery Packs
Some STANLEY battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOtE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Battery Packs
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include
catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust.
Inserting or removing the battery from the charger may ignite the
dust or fumes.
• Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non‑compatible
charger as battery pack may rupture, causing serious
personal injury.
• Charge the battery packs only in STANLEY chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations
where the temperature may fall below 4 ˚C (39.2 ˚F) (such
as outside sheds or metal buildings in winter), or reach
or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal
buildings in summer).
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium-ion battery packs are burned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek
medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if
exposed to spark or flame.

WARNING: Never attempt to open the battery pack for any
reason. If battery pack case is cracked or damaged, do not insert
into charger. Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (i.e., pierced with a nail,
hit with a hammer, stepped on). Electric shock or electrocution
may result. Damaged battery packs should be returned to service
centre for recycling.

WARNING: Fire hazard. Do not store or carry the battery
pack so that metal objects can contact exposed battery
terminals. For example, do not place the battery pack in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, etc.

CAUTION: When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand upright on
the battery pack but may be easily knocked over.
EngLIsh
25 25