Yamaha AW4416 Anleitung Seite 46

FORMAT No. 01111110 7E Universal Bulk Dump
01001100 4C 'L'
01001101 4D 'M'
00100000 20 ' '
00100000 20 ' '
00111000 38 '8'
01000011 42 'B'
00110011 39 '9'
00110110 38 '8'
DATA NAME 01000011 43 'C'
00100000 20 ' '
EOX 11110111 F7 End Of Exclusive
4.13.3 Parameter Change
4.13.3.1 Basic format
STATUS 11110000 F0 System Exclusive Message
ID No. 01000011 43 Manufacturer's ID (YAMAHA)
SUB STATUS 0pppnnnn pn p=mode (1:parameter change
or response for request
3:parameter request)
n=0-15(Rx Channel No.1-16)
GROUP ID 00111110 3E MODEL ID(Digital Mixer)
MODEL ID 00001000 08 Device Code(AW4416)
PARAM TYPE 0ttttttt tt Parameter type
DATA 0ddddddd dd0 data 0
: :
0ddddddd ddn data n
EOX 11110111 F7 End Of Exclusive
Parameter
type rx/tx function
------+------+-----------------------------------
0x00 rx/tx edit buffer (byte operation format)
0x01 rx/tx setup memory (byte operation format)
0x02 rx/tx function call (mem/lib recall,mem/lib
store)
0x10 rx/tx edit buffer (7bit operation format)
0x40 rx/tx edit buffer (bit operation format)
0x41 rx/tx setup memory (bit operation format)
0x43 rx/tx controller (key remote) (bit opera-
tion format)
4.13.3.2 Parameter Change
(byte operation for type 0x00:edit buffer)
4.13.3.2
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be
transmitted on the [Tx CH] MIDI channel when a param-
eter not specified in the [Control Change Assign Table] is
edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS 11110000 F0 System Exclusive Message
ID No. 01000011 43 Manufacturer's ID No.
(YAMAHA)
SUB STATUS 0001nnnn 1n parameter change or
response
Channel No.1-16)
GROUOP ID 00111110 3e MODEL ID(digital mixer)
MODEL ID 00001000 08 Device code (AW4416)
PARAM TYPE 00000000 00 byte operation for edit
buffer (type)
DATA 0aaaaaaa dd1 address( H) high 7 bits of
14 bits address
0aaaaaaa dd2 address( L) low 7 bits of
14 bits address
0000dddd dd3 data( H) high 4 bits of 8
bits data
0000dddd dd4 data( L) low 4 bits of 8
bits data
: : continuous address datas
EOX
The range of valid addresses is 0x0000 - 0x0595.
4.13.3.3 Parameter Change
(7bit operation for type 0x10:edit buffer)
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be trans-
mitted on the [Tx CH] MIDI channel when a parameter not
specified in the [Control Change Assign Table] is edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS
ID No.
SUB STATUS 0001nnnn 1n
GROUOP ID
MODEL ID
PARAM TYPE 00010000 10
DATA
EOX
The range of valid addresses is 0x0000 - 0x0595.
4.13.3.4 Parameter Change
(bit operation for type 0x40:edit buffer)
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be trans-
mitted on the [Tx CH] MIDI channel when a parameter not
specified in the [Control Change Assign Table] is edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS
ID No.
SUB STATUS 0001nnnn 1n
n=0-15(MIDI
GROUOP ID
MODEL ID
PARAM TYPE 01000000 40
DATA
EOX
The range of valid addresses is 0x0000 - 0x0595.
Version 2.0 Anleitung
11110111 F7 End Of Exclusive
11110000 F0 System Exclusive Message
01000011 43 Manufacturer's ID No.
(YAMAHA)
parameter change
15(MIDI Channel No.1-16)
00111110 3e MODEL ID(digital mixer)
00001000 08 Device code (AW4416)
7bit operation for edit
buffer (type)
0aaaaaaa dd0 address( H) high 7 bits of
14 bits address
0aaaaaaa dd1 address( L) low 7 bits of
14 bits address
0ddddddd dd2 data 7bit
: :
11110111 F7 End Of Exclusive
11110000 F0 System Exclusive Message
01000011 43 Manufacturer's ID No.
(YAMAHA)
parameter change
15(MIDI Channel No.1-16)
00111110 3e MODEL ID(digital mixer)
00001000 08 Device code (AW4416)
bit operation for edit
buffer (type)
0aaaaaaa dd0 address( H) high 7 bits of
14 bits address
0aaaaaaa dd1 address( L) low 7 bits of
14 bits address
0ddddddd dd2 data(bit0-2:change bit
no.0-7, bit3:0=reset
1=set)
: :
11110111 F7 End Of Exclusive
n=0-
n=0-
45