Herunterladen Inhalt Inhalt Diese Seite drucken

5.1 Preparation - IKRA Mogatec EGN 2500 Gebrauchsanweisung

Elektrischer gartenhäcksler
Vorschau ausblenden Andere Handbücher für EGN 2500:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

• If the unit emits unusual sounds or vibra-
tions, turn off the motor and look for the
cause. In general, vibrations are a sign of
problems.
• Ensure that the blade is firmly attached be-
fore you use the shredder. The device can
only be operated with a properly installed
blade.
• The shredder must be inspected carefully
before use. Only use machines that are in
proper functioning order. If you discover
any damage on or problems with the device
which could pose a risk to the user, have the
damage repaired before using the machine
again.
• Worn out or damaged components must be
replaced immediately for reasons of safety.
Only use original replacement parts. Using
non-original parts can lead to defective func-
tioning and injury.
• Only use the shredder in areas in which it
is protected from water. Do not expose the
device to rain.
• Store the shredder in a dry and secure loca-
tion and out of the reach of children.
• Younger,
disabled
may not use this device without supervi-
sion.
• Supervise children in the proximity of the de-
vice to ensure that they do not play with the
machine.

5.1 Preparation

• Do not allow children to work with this de-
vice.
• Do not use this device in the presence of by-
standers.
• Always wear ear and eye protection during
operation.
• Avoid wearing loose-fitting clothing and
clothing with hanging straps and bands.
• Only use the machine with plenty of open
space (e.g. not next to a wall or other fixed
objects) and on a solid, even surface.
• Do not use the machine on a paved surface
or on gravel where ejected objects could
case injury.
• Before using, check all screws, nuts bolts
and other fastening equipment to ensure
that they are secure. Also check the protec-
tion and shielding equipment. Replace dam-
GB | Operating Instructions
or
frail
individuals
aged and illegible stickers.
5.2 Operation
• Before activation, inspect the collection con-
tainer to ensure that it is empty.
• Do not place your face or body near the
feeding funnel.
• Do not place hands, other body parts, or
clothing into the feeding funnel or ejection
opening.
• Always place both feet on the ground se-
curely. Do not bend over the unit. When
feeding the machine never stand higher
than the surface on which the machine is
located.
• Always keep clear of the ejection area during
operation.
• When adding material thoroughly ensure
that there are no pieces of metal, stones,
bottles, cans or other foreign objects.
• If the a foreign object ends up in the cut-
ting mechanism or if the machine starts to
produce unusual noises or vibrations, shut
down the device, wait until the blade stops,
unplug the device from the mains, remove
the sparkplug cable and the sparkplug, and
proceed as follows:
1. Check the damages.
2. Check for loose parts and tighten them.
3. Replace any damaged parts or repair with
replacement parts (with the same specifi-
cations).
• Do not let the shredded material pile up in
the ejection area. This could prevent prop-
er ejection or cause this material to recoil
through the filling opening.
• If the machine starts to clog, shut it down
(unplug the device from the mains) before
fixing the clog. Keep the power unit free from
waste and other build-up to avoid damage
and potential risk of fire. Remember that
the blades continue to operate after the ma-
chine is shut down.
• Keep all protection and shielding equipment
in good condition.
• Do not tinker with the motor controller set-
tings. The controller regulates the safe
maximum speed and protects the motor and
all moving parts from damages caused by
excessive speeds. In the event of an issue,
seek out specialised help.
GB-5

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis