Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
and fitting sockets reduce the risk of electric
shock.
• Avoid physical contact with earthed sur-
faces as pipes, heaters, ovens and refrig-
erators. There is an increased risk of electric
shock if your body is earthed.
• Keep the tool out of the rain or moisture
in general. The penetration of water into
a power tool increases the risk of electric
shock.
• Do not use the cord to carry or hang up the
tool or to pull the plug out of the socket.
Keep the cord away from heat, oil and sharp
edges or moving parts of the tool. Damaged
or tangled cords increase the risk of electric
shock.
• When operating a power tool outdoors,
use exclusively extension cords that are
approved for outdoor-use. The use of an
extension cord that is suitable for outdoor
use reduces the risk of electric shock.
• If the operation of a power tool in a moist
environment cannot be avoided it is highly
recommended to use a residual current de-
vice (RCD). The use of an RCD reduces the
risk of electric shock.
4.3 Personal safety
• Always pay attention to what you do and
apply reasonable care when working with
a power tool. Do not use the power tool
when you are tired or under the influence of
medication, drugs or alcohol. When working
with power tools, even a short moment of
inattentiveness may result in severe injury.
• Wear personal protection equipment and al-
ways wear eye protection (safety goggles).
Wearing personal protection equipment as
a dust mask, nonslip safety shoes, safety
helmet or ear protectors (depending on the
type and application of the tool) reduces the
risk of injury.
• Avoid unintentional operation. Make sure
that the power tool is switched off before you
connect it to the mains supply and/or the
battery and whenever you pick up or carry
the tool. When carrying the tool with your
finger on the on/off switch or connecting the
tool to the mains supply with the switch in
'ON' position, this may result in accidents.
• Remove adjustment tools or wrenches and
GB | Operating Instructions
• Avoid unusual postures. Make sure to have
• Wear suitable clothes. Do not wear wide
• If dust extraction/collection devices are pro-
4.4 Use and handling of the power tool
• Do not overtax the power tool. Use the
• Do not use a power tool with a damaged
• Pull the mains plug and/or remove the
• Store power tools that are currently not
• Thoroughly maintain your power tool. Check
• Keep cutting tools sharp and clean. Thor-
GB-3
the like before you switch the power tool on.
A wrench or other tool that is inside or on a
rotating part of the tool may cause injury.
a safe footing and keep your balance at all
times. This will allow you to better control
the power tool in unexpected situations.
clothing or jewellery. Keep your hair, clothes
and gloves clear of all moving parts. Loose
clothing, jewellery or long hair may get
caught in moving parts.
vided make sure that they are connected
and used properly. The use of a dust ex-
traction device may reduce risks caused by
dust.
power tool intended for your type of work in
each case. The use of the suitable power
tool within the stated range of performance
makes working more effective and safer.
switch. A power tool that cannot be switched
on or off any more is dangerous and must
be repaired.
battery before adjusting a tool, changing
accessories or putting the tool aside. This
precaution avoids the unintentional start of
the tool.
used out of the reach of children. Do not
allow persons to use the tool if they are not
familiar with the tool or these instructions.
Power tools are dangerous if used by inex-
perienced persons.
whether moving parts are working properly
and are not jamming/sticking, and whether
parts are broken or otherwise damaged in
a way that may affect the function of the
power tool. Have damaged parts repaired
before using the tool. Many accidents are
the result of poorly maintained power tools.
oughly maintained cutting tools with sharp
cutting edges are jamming less often and
are easier to guide.
Werbung
Inhaltsverzeichnis
