Sharp RP-200H Bedienungsanleitung Seite 6

2.
3
3.
4.
4
5.
To remove lint or dust from the stylus, follow
the
(not supplied)
1) Never
2) Never use fingers or any objects
2 CABINET CLEANING
If you want to clean any part of the unit, wipe it with a damp cloth mois-
tened in methylated spirit (alcohol).
benzine, thinners, or household
4 EXCHANGE OF
The unit is dispatched
in
supply.
Pulley for 50Hz
a different
60Hz).
at the
pulley should be changed.
Pulley for 60Hz
The pulley
supply
60 Hz
Ditch
local SHARP
A *uitable cartridge has a yveight range from 4g
tp 9g and the distance from stylus tip to top of
cartridge
E
figure
facturer'$
installing
ap-200H/HB.
Slide the output lead connectors onto the new cartridge terminals,
tpking care to observe correct pQlarity ,
• White lead Left channel
Left channel
• Blue lead
Earth
5
Follow step I to step 4 and step 6 in the
instructions far "AUTOMATIC
given on page 4.
Move the cuing/pause control
wards.
Hold the headshel! grip and swing the tone-
arm to the playing position
table platter will start to rotate.
Move the cuing/pause control
to lower the tonearm onto
Follow step 9 to step 12 as given in the in-
structions for ' 'AUTOMATIC
page 4.
procedure in the illustration.
may be used.
NOTE:
move the brush in
direction because the stylus
damaged.
could damage the stylus.
Never use organic solvents such as
cleaners, or serious damage may result.
MOTOR PULLEY
from the factory
an area that has a 50Hz or
When the unit is used in an area having
mains supply frequency
the turntable platter will
correct speeds. Therefore
Note for users in Europe and Australia:
for operation on a 60Hz
is not fumished. This pulley
operation may be obtained
representative.
eges not exceed 19 mm.
on the left. Read the cartridge
fitting instrpctions carefully
a cartridge into the headshell of the
• Red lead
Right chan nel
Right chan nel
• Green lead
Earth
PLAY" as
lever back-
and the turn-
lever forward
the record.
PLAY" on
Sound distortion and record damage results when a worn-out stylus is used.
A soft brush The cartridge
sound reproduction
hours. Stylus
dealer or service
the lateral
may be
which
for use
60Hz mains
(50Hz or
not revolve
the motor
mains
for
from a
See the
manu-
before
52,5mm
The &scending position
automatic play was properly
the unit left the factory.
However, cartridge
.a -slight deviation,
I. Unplug the AC supply
outlet.
2. If the stylus descends outside the record
edge, turn the
stylus descends inside
turn the screw anti-clockwise.
One revolution
cending position
stylus supplied has a useful life of about 500 hours.
requires a change to a new stylus about every 500
assembly (part Nd. ST Y-120)
centre.
How to replace:
Switch off the unplifier
Remove the worn-out
2.
body of cartridge,
in the illustration.
3. Gently slide a new stylus assembly into the
body of cartridge.
How to exchange the Motor
. Loosen the pulley gru b-screw with a screw-
driver and slide
shaft.
2. Fit the correct
and fasten the grub-screw slightly.
3. Adjust the position
shaft so that the
$hown in Fig. A when
is set at "33";
the SPEED selector
4. Fasten the pulley
2. Place the cartridge
a distance gf 52,5 mm >etween the stylus
tip and the end of the headshell,
On this unit the headshet'
moved from the tonearm.
3. The trapking force
ment because the cartridge
(Refer to the instrugtions on page 3).
of the stylus during
adjusted before
change mav have caused
-requiring some adjustment.
tead from the AC
screw clockwise. If the
the starting groove,
of the screw alters the des-
about 10mm (3/8 in
Good
is available from a SHARP
power.
stylus assembly from
as indicated by the arrow
Pulley
the pulley from the motor
pulley onto the motor shaft
of the pulley on the
belt wilt be situated as
the SPEED selector
or as shown in Fig. B when
is setat "45".
grub-screw.
into the headshell with
NOTE:
cannot be re-
wil! require readjust-
weights differ.