Multiplex ROYALpro 7 Bedienungsanleitung Seite 334

pro
ROYAL
Menu I, call up New model
12.2.1.
12.2.2. Which model memory will be used?
Selecting the Template
12.2.3.
12.2.4. Selecting the servo configuration
Selecting the stick mode
12.2.5.
Selecting the Assignment
12.2.6.
Confirming with OK
12.2.7.
Entering the model Name
12.2.8.
12.3. Preparing the controls / switches.......... 34
12.3.1. Selecting / changing the idle position for spoiler /
throttle
12.3.2. Changing the switch ON position
12.4. Preparing servos ..................................... 35
12.4.1. Checking/changing the servo assignment
12.4.2. Checking/changing the direction of servo rotation 36
12.4.3. Calibrating servos = setting the centre and
maximum travels
12.5. Adjusting ailerons, and activating
landing aid (Mixer AILERON+) ................ 37
12.6. Differential aileron travel ........................ 38
12.6.1. Activating differential
12.6.2. Setting the differential value
12.7. Adjusting elevator, activating elevator
mixers (Mixer ELEVATR+)........................ 39
12.7.1. Spoiler to elevator = Spoiler compensation
(Spoiler input to ELEVATR+ mixer)
12.7.2. Throttle to elevator = Throttle compensation
(Thr -Tr input to ELEVATR+ mixer)
12.8. Activating inboard flaps (camber-
changing flaps) (Mixer FLAP+)............... 39
Activating the Spoiler input in the mixer
12.8.1.
FLAP+ (Butterfly)
Activating the Flap input in the mixer FLAP+
12.8.2.
(camber-changing flaps)
Activating the Aileron input in the
12.8.3.
FLAP+ mixer (aileron support by the inboard
(camber-changing) flaps)
Activating the Elevator-Tr (Ele -Tr) input
12.8.4.
in the FLAP+ mixer (snap-flap)
12.9. V-tail models ............................................ 41
12.9.1. Assigning V-tail servos
Activating the mixer V-TAIL+
12.9.2.
12.9.3. Checking/changing the direction of servo rotation 41
12.9.4. Adjusting the remaining inputs
12.10. Working with flight phases..................... 42
12.10.1. What is the purpose of switching between
different flight phases?
Default settings in the menu Flight phase
12.10.2.
12.10.3. Assigning flight phase switches
12.10.4. Locking / unlocking flight phases
12.10.5. Copying flight phases
12.10.6. Changing flight phase names
12.10.7. Setting a transition time
12.11. Supplementary functions ....................... 44
D/R and Expo
12.11.1.
12.11.2. Activating Combi-Switch
12.11.3. Motor run timer
13. Setting up a model helicopter
13.1. The method in principle .......................... 45
2
Setting up a New model in the Tx...........45
32 13.2.
Menu I, call up New model
32
13.2.1.
32 13.2.2. Which model memory will be used?
32 13.2.3. Selecting the template
Selecting the servo config(uration)
33 13.2.4.
Selecting the stick Mode
33 13.2.5.
Selecting the Assignment
33 13.2.6.
Confirming with OK
34 13.2.7.
Entering the model Name
13.2.8.
13.3. Preparing the controls / switches ..........47
34
13.3.1. Checking / changing control settings for idle /
35
collective pitch min. and throttle limiter min.
13.3.2. Changing the switch ON positions and / or the
switch assignment
35
13.4. Checking / changing the servo
Assignment..............................................48
36
13.5. Checking / adjusting the main rotor ......49
13.5.1. Checking / changing the direction of rotation
of the rotor head servos
13.5.2. Calibrating servos = setting the centre and
maximum travels
38
38
13.6. Checking / adjusting the tail rotor..........50
13.6.1. Checking / changing the direction of rotation
of the tail rotor servo
The TAIL mixer
13.6.2.
Offset value
13.6.3.
39
13.6.4. Collective pitch to tail (Revo-Mix)
Mixer Zero point
13.6.5.
39
13.6.6. Differential yaw (rudder) travel
Gyro ...........................................................51
13.7.
Parameter Type of Gyro
13.7.1.
13.7.2. Adjusting gyro suppression
40
13.8. Throttle, and associated functions ........53
13.8.1. What is the meaning of the terms Limiter, Curve,
40
Throttle Min., Trim, DTC and Throttle cut?
13.8.2. Throttle for electric helicopters
13.8.3. Throttle for I.C. powered helicopters
40
13.9. Setting the collective pitch curve...........55
41
Working with Flight phases..................55
13.10.
13.10.1. What is the purpose of switching between
different flight phases?
41
Default settings in the menu Flight phase
13.10.2.
41
13.10.3. Assigning flight phase switches
13.10.4. Locking / unlocking flight phases
42
13.10.5. Copying flight phases
13.10.6. Changing flight phase names
13.10.7. Setting a transition time
42
42
14. Main menu ¡Setup
42
Menu Transmitter..................................58
42
14.1.
43
Parameter Sound
14.1.1.
43
Parameter group Safety
14.1.2.
43
Parameter group Battery
14.1.3.
Parameter group Display
14.1.4.
44
Menu: Mixer def....................................59
14.2.
44
14.2.1. Defining a free mixer
44
14.2.2. Method of working / options for the mixer inputs 59
14.2.3. Making mixer inputs switchable
45
14.3. Menu: Assignment...................................61
Sub-menu Assign.Controls
14.3.1.
45
45
45
45
46
46
46
47
47
48
49
49
50
50
51
51
51
51
52
52
53
54
54
55
55
56
56
56
56
57
58
58
58
58
59
59
61
61