Servicing; Service/Manufacturer's Address; Repairs; Disassembly And Disposal - Elero Rolmotion M Nutzungsinformation

EU Declaration of conformity
Problem / Possible
Error cause
• Drive runs only • Faulty
in one direction
• Drive does not • No power
react
• Temperature
• Drive does • Random travel
not accept
programmed
end positions
• Travel to end
Fig. 7 Troubleshooting the RolMotion M
8

Servicing

The RolMotion M is maintenance-free.
9 Service/manufacturer's address
After installing the drive, the R+S mechatronics technician
(roller shutter and sun protection mechatronics technician)
must note the installed type of drive and the installation
location in the installation and operating instructions.
Drive designation
____________________
____________________
____________________
If malfunctions occur despite proper handling or if the unit
has been damaged, contact your contract partner.
elero GmbH
Drive technology
Maybachstr. 30
73278 Schlierbach
Deutschland / Germany
Please visit our website if you require a contact partner
outside Germany.
10

Repairs

Please contact your specialist if you have any questions.
Please always provide the following information:
• Item number and designation on the type plate
• Type of fault
• Accompanying conditions
• Your own theories regarding the cause of the problem
8 | EN
Remedial
action
• Check
connection connection
• Check mains
supply voltage
• Allow drive to
limiter has cool down
triggered
• Delete end
positions, re-
program end
positions
• Drive must
position or limit move, stop
stop too short briefly and
continue its
travel (as long
as a button
on the elero
assembly
cable is
pressed).
Installation location
(e.g. living room window 2)
_________________________
_________________________
_________________________
Tel: +49 7021 9539-0
Fax: +49 7021 9539-212
info.elero@niceforyou.cm
www.elero.com
11

Disassembly and disposal

After unpacking, dispose of the packaging in accordance
with the valid regulations.
Dispose of the product in accordance with the relevant
regulations when you no longer need it. Disposal is partially
subject to applicable legal regulations. Bring the product to
be disposed of to authorised collection points only.
Environmental information
No superfluous packaging materials have been used.
The packaging can be easily separated into three material
types: cardboard (box), polystyrene (padding) and
polyethylene (bag, protective foam).
The device is made of materials that can be reused if
dismantled by a specialist company. Please note the local
regulations on disposal of packaging materials and old
appliances.
On disassembly, additional dangers must be reckoned with,
which do not occur during operation.
Before disassembling the drive the system is to be
mechanically secured. The drive must not be forcibly
disconnected from the system.
Risk of injury due to electric current.
Risk of electric shock.
►Separate power supply cables physically and discharge
any energy accumulators still charged. After switching off
the device, wait at least 5 minutes so that the motor can
cool down and the voltage can be discharged from the
capacitors.
►During disassembly work above head height, use
suitable, inspected and structurally stable climbing aids.
►Work on the electrics may only be performed by
personnel described in the section "Safety notes on
electrical installation".
Removal for scrap
The international, national and regional laws and
regulations prevailing at the time of scrapping the product
must be observed.
Ensure that materials and components are recycled,
dismantled and separated properly in addition to observing
the environmental and health hazards relating to recycling
and disposal.
Environmental damage in case of incorrect disposal
►Electrical scrap and electronic components must be
handled as special waste and may only be disposed of by
approved specialist companies.
►Groups of materials such as various types of plastics and
metals must be separated before recycling/disposal.
Disposal of electrical and electronic components
The disposal and recycling of electrical and electronic
components must be carried out in accordance with the
relevant laws and national regulations.
© elero GmbH
WARNING
CAUTION