Variant C: Fixed Upper And Lower Limit Stop; Variant D: Upper End Position Freely; Adjustable, Fixed Lower Limit Stop; Troubleshooting - Elero Roltop Nutzungsinformation

Setting the end positions and the relief | Troubleshooting
Variant B: Fixed upper limit stop / lower end posi-
tion freely adjustable
③
Press the AB button ▼ again until the roller shutter
has reached the desired lower end stop.
The drive starts, stops briefly and then moves on
(while the button is pushed).
Correction is possible with the buttons ▲ and ▼ .
④
Press the AUF button ▲ until the drive stops auto-
matically.
Setting of the end positions variant B is now complete.
Fig. 9 End position setting Variant B:

5.6.8 Variant C: Fixed upper and lower limit stop

Variant C: Fixed upper and lower limit stop
①
From a middle blind position with the assembly
cable, push the UP button ▲ until the roller shutter
has reached the desired end position (run to the
upper stop).
The drive starts, stops briefly and then moves on
(while the UP button ▲ is pushed).
The drive switches off automatically when the upper
limit stop is reached.
②
Press the AB button ▼ until the drive stops auto-
matically.
The upper end position has been set.
Optional: Activation of the relief function for the
upper stop; see chapter 5.6.2
③
Press the AB button ▼ again until the roller shutter
has reached the lower end stop (run to lower end
stop).
The drive starts, stops briefly and then moves on
(while the DOWN button ▼ is pushed).
The drive switches off automatically when the lower
limit stop is reached.
④
Press the AUF button ▲ until the drive stops auto-
matically.
The lower end position has been set.
Optional: Activation of the relief function for the
lower stop; see chapter 5.6.3
Setting of the end positions variant C is now complete.
Fig. 10 End position setting Variant C:

5.6.9 Variant D: Upper end position freely

adjustable, fixed lower limit stop
Variant D: Upper end position freely adjustable,
fixed lower limit stop
①
From a middle blind position with the assembly
cable, push the UP button ▲ until the roller shutter
has reached the desired end position.
The drive starts, stops briefly and then moves on
(while the button is pushed).
Correction is possible with the buttons ▲ and ▼ .
②
Press the DOWN button ▼ until the drive stops
automatically.
The upper end position has been set.
6 | EN
Variant D: Upper end position freely adjustable,
③
Press the DOWN button ▼ again until the roller
shutter has reached the lower end stop (run to lower
end stop).
The drive starts, stops briefly and then moves on
(while the DOWN button ▼ is pushed).
The drive switches off automatically when the lower
limit stop is reached.
④
Press the
automatically.
The lower end position has been set.
Optional: Activation of the relief function for the
lower stop; see chapter 5.6.3
Setting of the end positions variant D is now complete.
Fig. 11 End position setting Variant D:
6

Troubleshooting

Problem /
Error
• Drive stops
during travel
• Drive stops
after a short
time
• Drive runs only
in one direction
• Drive not
responding
• Drive does not
learn any end
positions
Fig. 12 Error search at the RolTop
7

Servicing

The RolTop is maintenance free.
8

Repairs

Please contact your dealer if you have any questions.
Please always provide the following information:
• Item number and name on the type plate
• Type of fault
• Previous and unusual events
© elero GmbH
fixed lower limit stop
button until the drive stops
UP ▲
Possible Cure
cause
Remedy
• End positions • Set end posi-
are not set tions
• Drive is in
setting mode
• End position • Set second
programmed end position
• Sluggish • Check smooth
shutter running of the
roller shutter
• Connection • Check connec-
error tion
• No mains • Check mains
voltage voltage
• Temperature • Allow drive to
limiter has cool
tripped
• Random travel • Delete end
positions
Reset end
positions
• Travel to end • Drive must run,
position or limit stop briefly
stop too short and run on
(while a button
is pushed at
the assembly
cable).