MHZ art 01 Montageanleitung Seite 72

art_01 cassette awning installation instructions
Pull-out forces and bracket sets
Pull-out forces and bracket sets for wind resistance class 1
!
receive mounting brackets for installation on concrete (C 20/25) in the case of orders received which do not contain any information about the mounting substructure. Please note
forces depending on the insulating plaster thickness and the designed bracket set, as well as for installation on other substructures on request.
WALL installation on concrete C20/25
in cm 250 300 350
N 1.122 1.287 1.435
150
Set M KI KI KI
1.737 1.974 2.211
N
200
KI KI KI
Set M
N - 2.790 3.121
250
-
Set M KI KI
- - 4.192
N
300
- - KI
Set M
N - - -
350
-
Set M - -
WALL installation on brick Mz 12

in cm 250 300 350
N 1.122 1.278 1.435
150
KI KI KI
Set M
1.737 883 988
N
200
Set M KI KM KM
-
N 1.243 1.390
250
- KM KM
Set M
- - 1.863
N
300
Set M - - KM
-
N - -
350
- - -
Set M
WALL installation on hollow brick
in cm 250 300 350
504 575 143
N
150
KM KM KL
Set M
N 172 196 219
200
KL
Set M KL KL
- 276 309
N
250
- KL KL
Set M
N - - 415
300
-
Set M - KL
- - -
N
350
- - -
Set M
WALL installation on cellular concrete
in cm 250 300 350
1.122 575 645
N
150
Set M KI KM KM
777
N 883 988
200
KM KM KM
Set M
- 276 309
N
250
Set M - KL KL
-
N - 415
300
- - KL
Set M
- - -
N
350
-
Set M - -
Bracket set = provided bracket set (see overview on page 6)
X = on request
8
in cm
400 450 500
1.592 1.749 1.906
KI KI KI
2.448 2.685 2.921
KI KI KI
3.452 3.782 4.113
KI KI KI
4.630 5.069 5.507
KI KI KI
5.870 6.430 7.679
KI KI KI
in cm
400 450 500
1.592 1.749 856
KI KI KM
1.094 1.200 1.305
KM KM KM
1.538 1.685 1.832
KM KM KM
458 501 454
KL KL KL
580 635 759
KL KL KL
 HLz 12
in cm
400 450 500
158 174 189
KL KL KL
243 266 290
KL KL KL
342 375 407
KL KL KL
458 501 545
KL KL KL
580
X X
KL
 PB2
in cm
400 450 500
715 786 856
KM KM KM
290
1094 266
KM KL KL
342 375 407
KL KL KL
545
458 501
KL KL KL
580 635 759
KL KL KL
Information on recess installation
In contrast with wall or ceiling installation, no pull-out forces occur in the event
of recess installation, but rather shear forces. The maximum shear force for the
set for installation.
To install our HW bracket set, we recommend M12 steel screws (8.8) or M12
stainless steel screws (A2 70). The permissible shear stress of these screws is at
The installation and assembly information from the fastener manufacturers must
be observed.
Subject to technical changes, edition 03/2025