Replacing The Power Cable - EINHELL TE-MS 2112 L Originalbetriebsanleitung

turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described in section 5.5.
•
Cut as described in section 6.1.
6.5 Limiting the cutting depth (Fig. 3)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the
knurled nut on the screw (27). Turn the screw
(27) in or out to set the required cutting depth
and then retighten the knurled nut on the
screw (27).
•
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (22).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom.
Press the spring washer of the sawdust bag such
that it can be pushed onto the extractor connec-
tion (z) of the machine.
6.7 Changing the saw blade (Fig. 1, 14-15)
•
Before changing the saw blade: Pull out the
power plug!
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Press the saw shaft lock (5) with one hand
while positioning the Allen key (c) on the
flange bolt (31) with the other hand. The saw
shaft lock (5) engages after no more than one
rotation.
•
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remo-
ve the external flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12)in both perpendicular and
45° angle settings.
•
Important! The work to change and align the
GB
saw blade (7) must be carried out correctly.
6.8 Transport (Fig. 1-3)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Activate the release button (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
•
Carry the machine by the fixed transport
handle.
•
To set up the equipment again, proceed as
described in section 5.2.
6.9 Operating the laser (Fig. 2)
To switch on: Move the On/Off switch (36) to the
"I" position to switch on the laser (35). A laser line
is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch off : Move the On/Off switch (36) to the
"0" position.
6.10 Operating the LED lamp (Fig. 2)
•
For good illumination of the work area you
can use the LED lamp in addition to the room
lighting.
•
To switch on: Switch position „I"
•
To switch off: Switch position „0"
6.11 Electric brake
For safety reasons, the equipment is supplied
with an electric brake system for the saw blade.
The equipment may therefore emit an odor or
generate sparks when it is switched off . This has
no infl uence on the operational performance or
safety of the equipment.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 28 -