Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-SM 2131 Dual Originalbetriebsanleitung

•
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12) in both perpendicular and
45° angle settings.
•
Important! The work to change and align the
saw blade (7) must be carried out correctly.
6.8 Transport (Fig. 1-3)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Activate the release button (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
•
Fix the saw's drag function with the locking
screw for drag guide (24) in rear position.
•
Carry the equipment by the fixed saw table
(18) and the transport handle.
•
To set up the equipment again, proceed as
described in section 5.2.
6.9 Operating the laser (Fig. 3)
To switch on: Move the On/Off switch (36) to the
"I" position to switch on the laser (30). A laser line
is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch off : Move the On/Off switch (36) to the
"0" position.
6.10 Operating the LED lamp (Fig. 2)
•
For good illumination of the work area you
can use the LED lamp in addition to the room
lighting.
•
To switch on: Switch position „I"
•
To switch off: Switch position „0"
•
If the machine is equipped with an LED, this
LED is not allowed to be replaced by a diffe-
rent type of LED. Repairs are allowed to be
carried out only by the manufacturer of the
LED or one of his authorized agents.
6.11 Electric brake
For safety reasons, the equipment is supplied
with an electric brake system for the saw blade.
The equipment may therefore emit an odor or
generate sparks when it is switched off . This has
no infl uence on the operational performance or
safety of the equipment.
Anl_TE_SM_2131_Dual_SPK7.indb 29 Anl_TE_SM_2131_Dual_SPK7.indb 29
GB

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
- 29 -
13.05.14 16:04 13.05.14 16:04