Using The Whisk - Rondell Rde-1307 Betriebsanweisung

•
After you finish using the unit, take the power plug out
of the socket and remove the blender attachment (6),
pressing the lock buttons (5).
Attention!
– Do not remove the blender attachment (6) during
operation.
– To avoid damage to the blades, do not process too
hard products such as cereals, rice, spices, coffee
beans, ice, cheese, frozen food.
– If the products are difficult to process, add some liq-
uid into the bowl.

USING THE WHISK

Use the whisk attachment (8) only for beating cream or egg
whites, making biscuit dough or for mixing ready desserts.
Warning: before assembling make sure that the pow-
er plug is not inserted into the mains socket.
•
Insert the whisk (8) into the gear (7) and press on it
until bumping.
•
Insert the whisk gear (7) into the motor unit (4)
and slightly press on it until the locks (5) clicking.
Instructions for assembling are shown in pic. 2.
•
Make sure that the attachment is fixed properly.
•
Insert the power plug into the mains socket.
•
Sink the whisk (8) into the bowl with products.
•
Set the required operation speed using the control
knob (1).
•
To switch the unit on, press and hold down the button
(2). Use this operation mode for mixing liquid products.
•
After using the device, unplug the power cord from the
socket, remove the whisk (8) from the whisk gear (7),
and disconnect the gear (7) from the motor unit (4) by
pressing the locks (5).
Attention!
– Do not use the whisk (8) to make tight dough.
– Products for beating/mixing should be put into the
bowl before the unit is switched on.
USING THE MASH MAKING ATTACHMENT
Attention!
The attachment (9) is used to make the mash from
boiled potatoes, carrot or other vegetables.
– To make mash, it is recommended to use mealy sorts
of potato.
– Do not immerse the mash making attachment into boil-
ing liquids, for example, when cooking soup.
– Do not use the attachment (9) for processing hard prod-
ucts and products that haven't passed temperature pro-
cessing, because it can damage the attachment.
Warning: before assembling make sure that the pow-
er plug is not inserted into the mains socket.
•
Insert the blender attachment (9) into the motor unit
(4) and slightly press on it until the locks (5) click-
ing. Instructions for assembling and use are shown
in pic. 3.
•
Make sure that the attachment is fixed properly.
•
Insert the power plug into the mains socket.
•
Immerse the attachment (9) into the bowl with prod-
ucts.
•
Set the required operation speed using the control
knob (1).
•
To switch the unit on, press and hold down the button (2).
•
When the button (3) is pressed, the attachment (9)
operates at maximal rotation speed.
•
After you finish using the unit, take the power plug out
of the mains socket and remove the attachment (9)
from the motor unit (4), pressing the locks (5).
USING THE CHOPPING KNIFE
Attention! – Do not grind very hard products such as
nutmeg, coffee beans and cereals.
Before you start chopping:
– Remove bones, sinews and cartilage from meat.
– Cut meat, onion, garlic, carrots etc. into approximately
equal slices.
– When chopping greens, remove stems of herbs.
Chopping
Warning:
– Before assembling, make sure that the power plug is
not inserted into the mains socket.
– Do not overload the processing bowl!
Attention! Be careful, the knife blades are very sharp!
•
Remove the plastic protection from the сhopping knife
blades (16) and place the knife (16) on the bowl (14)
shaft by grasping its upper part (the shaft is in the cen-
ter, at the bottom of the bowl). Instructions for assem-
bling are shown in pic. 4.
•
Put the products into the chopper bowl (14).
•
Install the geared lid (10) on the chopper bowl (14).
•
Align the « » symbol on the lid (10) with the mark on
the handle of the chopper bowl (14) and place the lid on
the bowl, then turn the lid clockwise until it clicks, the
15
ENGLISH