Using The Whisk; Using The Chopper - Rondell Rde-1301 Betriebsanweisung

ENGLISH

USING THE WHISK

Use the whisk attachment (11) only for beating cream and egg
whites, making biscuit dough or for mixing ready desserts.
WARNING: Before installing the whisk (11) and the gear
(12) make sure that the power plug is not inserted into the
mains socket.
•
Insert the whisk attachment (11) into the whisk gear (12).
•
Insert the whisk gear (12) into the motor unit (3) and turn it
counterclockwise until bumping, make sure that the gear
(12) and the whisk (11) are fixed properly.
•
Insert the power plug into the mains socket. Put the whisk
attachment (11) into the bowl with products.
•
Put the whisk attachment (11) into the bowl with products.
Note: You can put the foodstuffs into the measuring cup (10).
•
To switch the unit on, press and hold down the button (5).
Turn the attachment rotation speed control knob (6) to
change the whisk (11) rotation speed.
•
If you press and hold down the «TURBO» button (4), the
unit will operate at maximum rotation speed.
•
After you finish using the unit, take the power plug out of
the mains socket, disconnect the whisk gear (12) from the
motor unit (3) by turning it clockwise.
•
Remove the whisk (11) from the gear (12).
ATTENTION!
– Do not use the whisk attachment (11) to knead tight
dough.
– Put products into the bowl before switching the unit on.

USING THE CHOPPER

The chopper is used to chop meat, cheese, onion, herbs, gar-
lic, carrots, walnuts, almonds, prunes, vegetables and fruit.
ATTENTION!
Do not chop very hard products, such as ice cubes, frozen
products, nutmegs, coffee beans, cereals etc.
Before you start chopping:
– Cut meat, cheese, onions, vegetables or fruit into pieces
approximately 2x2 cm in size.
To achieve the best results, refer to the table below:
Function
Chopping (chopper)
Chopping and mixing
(Blender)
Beating (Whisk)
Note: all data in this table are given as recommendations.
– Remove stems of herbs, shell nuts.
– Remove bones, sinews and cartilage from meat.
Chopping
Caution: the blades of the chopping knife (8) are very sharp!
Always hold the chopping knife (8) by the upper plastic end.
•
•
•
Note: Do not switch the unit on when the chopper bowl (7)
is empty.
•
•
•
– To connect the unit to the mains, insert the power plug into
– To switch the unit on, press and hold down the button (5).
– If you press and hold down the «TURBO» button (4), the
– During the unit operation hold the motor unit (3) with one
– After using the unit, wait until the chopping knife (8) fully stops.
– Unplug the unit.
– Disconnect the motor unit (3) from the geared lid (9) feed-
– Remove the geared lid (9).
– Carefully remove the chopping knife (8) taking it by the
– Take the chopped food out of the chopper bowl (7).
ATTENTION!
Strictly follow the described sequence of operations.
Product type Maximum weight
meat 150 g
Carrot + water 240 g (carrot)
360 g (water)
Egg whites
6
Place the chopper bowl (7) on a flat stable surface.
Set the chopping knife (8) on the axis inside the chop-
per bowl (7).
Put the products into the chopper bowl (7).
Place the geared lid (9) on the chopper bowl (7) and rotate
it clockwise until bumping.
Install the motor unit (3) on the geared lid (9) feeding
chute, turn it counterclockwise until bumping, make sure
that the motor unit (3) is fixed properly.
Install the motor unit (3) strictly in the vertical position
and evenly.
the mains socket.
Turn the attachment rotation speed control knob (6) to
change the chopping knife (8) rotation speed.
chopping knife (8) will rotate at maximum rotation speed.
hand and the chopper bowl (7) with the other hand.
ing chute by turning it clockwise.
plastic end.
Approximate processing
time, seconds
10
60
90
Speed
TURBO
TURBO
TURBO