RONDELL RDE-1307 Betriebsanweisung Seite 16

ENGLISH
mark on the handle of the bowl (14) and the «
bol on the lid (10) should match.
•
Place the motor block (4) on the geared lid (10) and
press it lightly until the locks (5) click.
•
Insert the power plug into the mains socket.
•
Set the required speed with the control knob (1).
•
To switch the unit on, press and hold down the button (2).
•
When the button (3) is pressed, the knife (16) rotates at
maximum rotation speed.
•
Hold the motor unit (4) with one hand and the bowl (14)
with the other hand during operation.
•
After you finish using the unit, take the power plug
out of the socket, press the locks (5), and remove the
motor unit (4) from the lid (10).
•
Then remove the geared lid (10) from the bowl (14) by
pressing the button (15) and turning the lid (10) coun-
terclockwise.
•
Carefully remove the knife (16) by grasping its top.
•
Take the chopped products out of the chopper bowl (14).
•
Clean, wash and dry all the used parts immediately
after operation.
•
Put the knife (16) into the plastic protective cover.
Attention! Continuous operation time of the unit should
not exceed 20-30 seconds.
USING THE DISC (SHREDDING/SLICING)
•
Place the base (18) on the axle of the bowl (14) (the
axle is in the center, on the bottom of the bowl).
•
Place the disc (17) on the base (18). Instructions for
assembling are shown in pic. 5.
Attention! Be careful, the disc blades are very sharp!
•
Align the « » symbol on the lid (10) with the mark on
the handle of the chopper bowl (14) and place the lid on
the bowl, then turn the lid clockwise until it clicks, the
mark on the handle of the bowl (14) and the «
bol on the lid (10) should match.
•
Place the motor block (4) on the geared lid (10) and
press it lightly until the locks (5) click.
•
Insert the power plug into the mains socket.
•
Set the required speed with the control knob (1).
•
To switch the unit on, press and hold down the button (2).
•
When the button (3) is pressed, the disc (17) rotates at
maximal rotation speed.
•
Place the products into the feeding chute of the geared
lid (10); use the pusher (19) for food feeding.
•
Press the pusher gently while feeding products.
•
» sym- After using the unit, unplug the power cord from the
socket, press the locks (5), and disconnect the motor
unit (4) from the geared lid (10).
•
Then remove the geared lid (10) from the bowl (14) by
pressing the button (15) and turning the lid (10) coun-
terclockwise.
•
Carefully remove the base (18) together with the
mounted disc (18).
•
Take the chopped products out of the chopper bowl (14).
•
Clean, wash and dry all the used parts immediately
after operation.
Attention! Place products to be processed in the feeding
chute of the lid (10) and shove it with the pusher (19) to
feed it, never use your fingers or utensils.
USING THE CUBIC ATTACHMENT
Use the cubic attachment for cutting fruit, some raw and
boiled vegetables.
Attention!
– Do not process solid ingredients such as fruit with
bones, meat with bones, or frozen foods. They can
block and damage the cubic attachment.
Tip: if you want to chop different ingredients without
cleaning the grate (13) during chopping, always start with
the softest ingredients.
For instance, to make a fruit salad, start with banana,
then proceed with mango and finish with apples.
Note: If ingredients get stuck, unplug the appliance, discon-
nect the motor unit (4), open the lid (10) by turning it clock-
wise and remove the ingredients stuck in the feeding chute
of the lid (10). Use the pusher (20) to push the ingredients
stuck in the cubic attachment grid (13) into the bowl (14).
– Pre-cut large ingredients into pieces to fit them freely
in the feeding chute of the lid (10).
» sym- – If you need to chop a large number of ingredients,
process in small batches (250g max) and shake the
bowl lightly to evenly distribute the chopped ingredi-
ents in the bowl.
Warning: before assembling make sure that the power
plug is not inserted into the socket.
•
Insert the cubic attachment grid (13) into the cubic attach-
ment (12). Instructions for assembling are shown in pic. 6.
•
Insert the assembled cubic attachment (12) into the
bowl (14).
•
Align the slots on the side surface of the сubic attach-
ment (12) with the protrusions inside the chopper
16