Before The First Use; Using The Blender; Cleaning And Care - Rondell Rde-1252 Betriebsanweisung

BEFORE THE FIRST USE

After unit transportation or storage at low temperature
keep it for at least three hours at room temperature before
switching on.
•
Unpack the unit completely and remove any advertising
stickers that can prevent the unit operation.
•
Check the unit for damages, do not use a damaged unit.
•
Before switching the unit on, make sure that your home
mains voltage corresponds to the unit operating voltage.
•
The unit is intended for operation with AC system and 50 or
60 Hz frequency. The unit does not need any additional set-
tings for operating with the required nominal frequency.
•
Before the first use wash all the removable parts (1, 2, 3) with
warm water and neutral detergent and then dry thoroughly.
•
Clean the motor unit (5) with a soft, slightly damp cloth
and then wipe it dry.
•
Do not immerse the motor unit (5) into any liquids and do not
wash it with water.
•
Place the blender on a flat stable surface.
ATTENTION! Continuous operation time of the blender should
not exceed 180 seconds, and the break between operations
should be 1-2 minutes.
•
Do not remove the blender bowl (3) and the bowl lid (2)
during the operation.

USING THE BLENDER

The blender is used for chopping products, mixing various
ingredients and making cocktails.
•
Place the blender bowl (3) on the motor unit (5) matching the
ledges on the bottom part of the bowl (3) with the grooves on
the motor unit (5), turn the bowl (3) clockwise until bumping.
•
Make sure that the operation mode switch (6) is set to the
position «0».
•
Remove the blender bowl lid (2).
•
Put the necessary ingredients into the bowl (3).
Note: Maximal capacity of the glass bowl (3) is 1500 ml. To
avoid possible foam forming or spilling during processing of
foamy liquids or low-density liquids, such as milk, do not ex-
ceed the mark 1000 ml on the pitcher.
•
Cover the blender bowl (3) with the lid (2), insert the mea-
suring cup (1) into the lid (2) opening and turn it clockwise
until bumping.
•
Make sure once again that the blender bowl (3) is installed
correctly.
•
Insert the power plug into the mains socket.
Note: The blender will not be switched on if the blender bowl
(3) is installed incorrectly.
•
Use the operation mode switch (6) to set the required rota-
tion speed of the knives:
«1» (low speed) - for mixing liquid products.
«2» (high speed) - for liquid and hard products.
«P» - pulse mode.
•
To switch the pulse mode on, set the switch (6) to the posi-
tion "P" and hold it.
•
During the operation or between the operation cycles, you
can add the required ingredients into the bowl (3). To do
this, remove the measuring cup (1) turning it counter-
clockwise, you can use the measuring cup (1) as a bowl for
adding necessary liquid ingredients. After adding the ingre-
dients, place the cup (1) back to its place and turn it clock-
wise until bumping.
•
After the unit's operation is finished, set the operation mode
switch (6) to the "0" position and unplug the unit.
•
Remove the blender bowl (3) from the motor unit (5) by turn-
ing it counterclockwise until bumping.
•
Remove the lid (2) from the bowl (3) and take the processed
products out of the bowl (3).
•
After the operation is finished, wash the blender bowl (3).
Note: If food processing is hindered, add some liquid (water,
liquor, juice) into the blender bowl (3).
•
Before starting to chop/mix, we recommend to peel fruit,
remove inedible parts, such as stones, and cut fruit into
2х2 cm cubes.
ATTENTION! Continuous operation time of the blender should
not exceed 180 seconds, and the break between operations
should be 1-2 minutes.

CLEANING AND CARE

After the unit operation is finished, switch the blender off by
setting the operation mode switch (6) to the "0" position and
unplug it.
•
Remove the blender bowl (3) from the motor unit (5) by turn-
ing it counterclockwise until bumping.
•
Remove the lid (2) and take the processed products out of
the bowl (3).
•
Wash the bowl (3) preliminarily. Set the bowl (3) on the motor
unit (5) matching the ledges on the bottom part of the bowl
(3) with the grooves on the motor unit (5), turn the bowl (3)
clockwise until bumping.
•
Make sure that the operation mode switch (6) is set to the
position «0».
9
ENGLISH