Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The hammerdrill can be fitted with different bits depending on
the desired application. Use sharp drill bits only.
Bit Recomendations
•
For wood, use twist bits, spade bits, power auger bits or
hole saws.
•
For metal, use high-speed steel twist drill bits or hole saws.
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry.
•
For masonry, such as brick, cement, cinder block, etc., use
carbide-tipped bits rated for percussion drilling.
SDS plus® Bit Holder (Fig. G)
nOTE: Special adapters are needed to use the SDS plus® tool
holder with straight shank bits and hexagonal screwdriver bits.
Refer to Optional Accessories.
To insert a drill bit or other accessory:
1. Insert the shank of the bit about 19 mm into SDS plus®
tool holder
9
.
2. Push and rotate bit until it locks in place. The bit will be
securely held.
3. To release bit, pull the sleeve
Keyless Chuck Removal (Fig. G,I)
DCH417 only
On some hammerdrills, a keyless chuck can be installed in place
of the SDS plus® bit holder.
WARNING: Never use standard chucks in the rotary
hammering mode.
Replacing the sDs plus® Bit holder with the keyless
chuck (Fig. I)
1. Select hammering only mode (see Operation Modes), this
locks the spindle to prevent it from rotating when unlocking
the removable tool holder.
2. Turn the locking collar
10
pull the installed bit holder off.
3. Push the keyless chuck
the locking collar
10
into the locking position.
4. To replace the keyless chuck with the SDS plus® bit holder,
first remove the keyless chuck the same way as the SDS
plus® bit holder was removed.
5. Then replace the SDS plus® bit holder the same way as the
keyless chuck was replaced.
To Insert a Drill Bit or accessory in keyless chuck (Fig. G)
1. Grasp the sleeve
22
of the keyless chuck
and use the other hand grasping the base of the chuck.
2. Rotate the sleeve
22
counterclockwise (as viewed from the
front) far enough to accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full gripping power.
4. Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
5. To release the accessory, repeat Steps 1 and 2 above.
back and remove the bit.
20
into the unlocked position and
23
onto the spindle
21
and turn
23
with one hand
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A, H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
with the other hand on the side handle
Operation Modes (Fig. A)
WARNING: Do not select the operating mode when the
tool is running.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
symbol
Mode
Rotary Drilling
Rotary
hammering
hammering
only
To select an Operating Mode
1. Depress the mode selector release button
2. Rotate the mode selector dial
the symbol corresponding with the desired mode.
nOTE: The mode selector dial
rotary hammering or hammering only mode at all times. There
are no operable positions in between. It may be necessary to
briefly run the motor after having changed from 'hammering
only' to 'rotary' modes in order to align the gears.
Performing an Application (Fig. A)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to the material.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
EnGLIsh
.
5
3
to select the
application
Screwdriving
Drilling into steel, wood
and plastics
Drilling into concrete and
masonry
Light chipping
.
4
3
so that the arrow points to
must be in rotary drilling,
3
,
8
37
Werbung
