Felisatti SRF305/1800 Bedienungsanleitung Seite 12

Outside Corner
Mitre Angle
Bevel Angle
Moulding
Position
Finished Side
NOTE:
1. These special stops can not be used with 45° crown
moulding.
2. Since most rooms do not have angles of exactly
90°, fine tune is needed and always take a test cut to
confirm the correct angles.
Pullover Cut (Fig. 23)
WARNING!
- Never pull the cutting head assembly and spinning
blade toward you during the cut. The blade may try to climb
up on the top of the workpiece, causing the cutting head
assembly and spinning blade to kick back.
- Never lower spinning saw blade down before pulling
the cutting head to the front of the saw.
1. Unlock the carriage lock handle (1) and allow the
cutting head assembly to move freely.
2. Set both the desired bevel angle and/or the mitre
angle and lock into position.
3. If bevel cutting, set both the left and right sliding
fences (2) to their proper location.
4. Use a hold down clamp to secure the workpiece.
5. Grasp the saw handle (3) and pull the carriage (4)
forward until the centre of the saw blade is over the front of
the workpiece (5).
6. Pull the trigger (6) to turn the saw on.
7. When the saw reaches full speed, push the saw
handle down, slowly, cutting through the leading edge of
the workpiece.
8. Slowly move the saw handle toward the fence,
completing the cut.
9. Release the trigger and allow the blade to stop
spinning before allowing the cutting head to raise.
Setting Cutting Depth (Fig. 24)
The depth of cut can be preset for even and repetitive
shallow cuts.
1. Adjust the cutting head down until the teeth of the
blade are at the desired depth of cut.
2. While holding the upper arm in position, turn the
stop knob (1) until it touches the stop plate (2).
3. Recheck the blade depth by moving the cutting
head front to back through the full motion of a typical cut
along the control arm.
The Arbour Laser Guide
Your tool is equipped with our latest innovation, the
Arbour Laser Guide, a battery powered device using
Class 1M laser beams. The laser beams will enable you
to preview the mitre blade path on the workpiece to be cut
before you begin your operation.
DANGER! Laser is activated when blade is rotating.
Do not stare into beam or view directly with optical
instruments. Do not remove the warning label affixed
to the blade guard. Avoid direct eye contact with light
source.
NOTE: The red laser line will appear as a dotted line
when the motor is activated and the blade assembly is in
the uppermost position. This broken line will assist you in
aligning the mark on your workpiece with the cutting path
of the saw blade. As you lower the blade assembly, the
12
31.6° Left 31.6° Right
33.9° 33.9°
bottom against top against
fence fence
Keep right side Keep right side
of cut of cut
retractable guard will lift and turn the broken line into a solid
red laser line.
Laser Warning Label: Laser radiation does not view
directly with optical instruments class 1M laser product
<0.39mW, 400-700nm, CW, Acc.IEC 60825-1:2007
OPERATION OF LASER
With the blade assembly in the uppermost position:
1. Position your workpiece onto the mitre saw.
2. Turn on the mitre saw to activate the laser beam.
3. Verify the laser beam is aligned with the mark on the
workpiece.
WARNING! Do not lower the blade assembly during
the alignment process.
4. If the mark on the workpiece is not aligned with the
dotted laser line, turn off machine, wait for the blade to stop
and reposition workpiece.
5. Turn on the mitre saw and verify alignment.
6. Once alignment is achieved, secure workpiece with
a clamping device and perform the cut.
VARIABLE SPEED SWITCH (Fig. 1) (Mod.
SRF305/1800E)
This saw is equipped with a variable speed control
dial (26). The blade stroke rate can be adjusted by
simply rotating the dial. To increase speed, rotate the dial
clockwise. To reduce speed, rotate the dial anti-clockwise.
CHANGING BLADES (Fig. 25, 26, 27)
WARNING! To avoid injury from accidental starting,
always turn the switch off and remove the power plug from
the power source before changing the blades.
Use correctly sharped saw blades. Observe the
maximum speed and tooth type marked on the saw blade.
Blade replacement procedure including the method for
repositioning that this must be carried out correctly. Do not
use a saw blade which is not recommended in this owner's
manual.
Removing the Blade
1. Unplug the saw from the outlet
2. Raise the mitre saw to the upright position.
3. Raise the lower clear plastic blade guard (1) to the
uppermost position. (Fig. 25)
4. While holding the lower blade guard, loosen the
cover plate screw (2) with a Phillips screwdriver.
5. Rotate the cover plate (3) to expose the arbour bolt
(4).
6. Place the blade end wrench over the arbour bolt
7. Locate the arbour lock (5) on the motor, below the
belt cover. (Fig. 26)
8. Press the arbour lock, holding it in firmly while
turning the blade clockwise. The arbour lock will then
engage and lock the arbour. Continue to hold the arbour
lock, while turning the wrench clockwise to loosen the
arbour bolt.
9. Remove the arbour bolt (5), the laser collar (6), and
the blade (7). Do not remove the inner blade collar. (Fig.
27)
10. Raise the lower clear plastic blade guard (1) to the
upright position (Fig. 25) to remove the blade.
NOTE: Pay attention to the pieces removed, noting
their position and direction they face. Wipe the blade
collars clean of any sawdust before installing a new blade.
Also, the 305 mm blade has a 25.4mm arbour hole with a
15.9 mm reducer to mount onto the saw.
Installing Blade
Un-plug the mitre saw before changing/installing the
blade.