Kärcher K 5 Power Control Bedienungsanleitung Seite 13

*KÄRCHER suction hose for water supply from
30
open containers (order no. 2.643-100)
Included screws and dowels
31
* additionally required
Supplied screws and dowels
Illustration C
Stand dowels (2 pieces)
1
Screw 4x22 (2 pieces)
2
Screw 4x16 (10 pieces)
3
Safety devices
WARNING
Danger of injury!
Serious injuries due to missing, modified or ineffective
safety devices.
Do not bypass or remove the safety devices and do not
render them ineffective. Safety devices are provided for
your own protection.
Power switch
The power switch prevents unintentional operation of
the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and
prevents the device from starting unintentionally.
Auto-stop function
If the lever of the high-pressure gun is released, the
pressure switch turns off the pump and the high-pres-
sure jet stops. The pump switches on again when the le-
ver is pressed.
Motor circuit breaker
The motor circuit breaker shuts off the device if power
consumption it too high.
Symbols on the device
Do not aim the high-pressure jet may at per-
sons, animals, live electrical equipment or
the device itself.
Protect the device against frost.
The device may not be connected to the
public drinking water network.
Installation
For the illustrations, refer to the graphics page.
Fit the supplied loose parts onto the device before start-
ing up the device.
Have the included screws and the appropriate screw-
driver ready.
Fitting the wheels
1. Insert the wheels.
Note
Pay attention to the alignment of the hole.
Illustration D
2. Secure the wheels with 1 screw each.
Mounting the stand
1. Insert the stand.
Illustration E
2. Insert the 2 dowels into the holes as far as they will
go.
3. Secure the base with 2 screws.
Mounting the storage for spray lances
1. Hook in the storage for the spray lances.
2. Secure the storage with 2 screws.
Illustration F
3. Secure the cover with 4 screws.
Illustration G
Mounting the transport handle
1. Attach the transport handle.
Illustration H
Mounting the accessory net
1. Hang the accessory net on the hooks.
Illustration I
Push the high-pressure hose through the
1. Insert the high-pressure hose through the hose
guide from the rear.
Illustration J
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration K
1. Place the device on a level surface.
2. Completely unwind the high-pressure.
3. Pull the high-pressure hose completely forward
through the hose guide and eliminate any loops and
twists.
4. Insert the high-pressure hose into the high-pressure
gun until it audibly clicks into place.
Note
Take care to ensure the correct alignment of the nipple.
Illustration L
5. Check the secure connection by pulling on the high-
pressure hose.
6. Plug the mains plug into a mains socket.
For the connection values, see the type plate or chapter
Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water
Contamination in the water can damage the pump and
the accessories.
KÄRCHER recommends using the KÄRCHER water fil-
ter for protection(special accessory, order number
4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connec-
tion of the device
Damage to the pump
Never use a hose coupling with Aquastop on the water
connection of the device.
You can use an Aquastop coupling on the tap.
1. Plug the garden hose onto the water connection
coupling.
2. Connect the garden hose to the water line.
3. Open the water tap fully.
Illustration M
Suck water from open containers
This high-pressure cleaner with the KÄRCHER suction
hose is suitable for sucking in surface water, e.g.from
English
hose guide
Initial startup
Water supply
13