Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CONTENTS
A.
ASSEMBLY
INSTRUCTIONS
Assembly
Safety
Hooking up
Applications
Recommendations concerning the work area
B.
GENERAL
POWER
TOOL
c.
KNOW
YOUR
PRODUCT
D.
STARTING
THE
MACHINE
Items to be checked before starting
Switching on and Off
Mechanical and electronic speed regulator (RUBIMlX-9BL)
Electronic
speed regulator
A. ASSEMBLY
INSTRUCTIONS
Assembly
Once you have unpacked your machine, check to make sure
that there are no damaged or broken parts. If there are, and
you need to change these components they must only be
replaced by original of the manufacturer, otherwise the GS
mark can be not valid (if in doubt, consult the manufacturer).
Safety
Readcarefully and understand the safety measures before the
use of the machine.
For safe operation on the grinder, the operating and safety
instructions must be fully read and strictly observed.
Hooking up
Check that the voltage and frequency of the machine shown on
the characteristics plate match the electric system.
Coil feeding cable during transport.
by tugging at the cable.
Applications
The machine is intended for stirring powder-type building
materials such as mortar, plaster, cement, and solvent-free
paints, varnish and similar substances.
The user alone is responsible for any liabilities caused by usage
other
than intended.
Recommendations
concerning the work area
Pay close attention to the state of the area where the job is to
be done. Keep it clean and well lit. The machine should be kept
clean at all times in order to ensure optimum performance and
the safestworking conditions.
Do not open dispose of it through the available collection
points.
B.
GENERAL
POWER
TOOL
WARNING!
When using electrical tools, you must
always follow the basic security precautions in order to
reduce the risk of fire, electrical shock and personal
injuries. Carefully read these instructions before using
this product and keep them.
This machine complies with 98/37/EC, EN 60745-1:2006,
2.
EN 60745-2-1 IAI 1:2007 regulations.
3.
Once you have unpacked your machine, check to make
sure that there are no damaged or broken parts. If there
are, have these replaced by original components. Should
they be electrical components, exchange them for
officially authorised apparatuses with the same reference
number (if in doubt, consult the manufacturer).
4.
Check that the voltage and frequency of the machine
shown on the characteristics plate match the electric
system.
ENGLISH
SAFETY
WARNINGS
the machine
(RUBIMlX-9BL DUPLEX)
Never move the machine
SAFETY
WARNINGS
E.
INSTRUCTIONS
FOR
F.
MAINTENANCE
Cleaning and maintenance
Storage
G.
GENERAL
CHARACTERISTICS
Technical
characteristics
Electric mitring
saws for tiles
Exploding
H.
DECALARATION
OF
REGULATIONS
5.
To ensure total safety, use gloves, chest covering,
protective gogglesand sound protection.
6.
DO not use baggy clothing or jewelry which could get
caught by moving parts.
7.
Anti-slip
footwear
outdoors.
8.
Use protective caps for long hair.
9.
Keep the worksite clean. Untidy work areasand benches
can causeaccidents and damage.
10.
Never risk leaving the machines out in the rain or snow.
Do not use the machine in wet or damp places. Keep the
worksite
well
lit at all times.
around inflammable liquids or gases.
Avoid physical contact with surfaces which are framed or
11.
connected
to earth.
12.
Prevent anyone not involved with the work at hand,
especially children, from touching the machine and the
extensible cables. Keep unauthorised personnel away
from
the worksite.
13.
When
not in use, the machine
closed, dry place, out of the reach of children.
14.
This machine will provide better, safer performance if
used only for the task for which it has been designated.
15.
Do not force a small machine to do the work ofa larger
one.
Do not use this machine for purposes other than those
16.
described
in the instructions
17.
Never tug at the cable in order to disconnect the
machine.
18.
Stand firmly on the floor and be careful at all times not to
lose your balance.
Keep cutting tools clean and sharp for better, safer
19.
performance.
20.
Periodically examine the machine cables and if they are
damaged, repair them through an authorized service.
21.
Periodically check the cablesof this machine. Should they
show signs Ofdamage.
Keep holders clean, dry and free of grease and oil.
22.
When not in use, before repair and when accessories
23.
such as saw blades, bits and blades are replaced,
disconnect the machine from the power outlet.
24.
Get used to verifying that the monkey wrenches and
adjustable spanners are taken out Of the machine before
operation.
Make sure that the switch is in the "OFF" position when
25.
pluggingin the machine.
26.
When using the machine outdoors, use only extensible
cord designed for this purpose.
27.
Keep a close eye on what you are doing, use your
common
sense and do not use the machine
6
USE
COMPLIANCE
WITH
EEC
is recommended
when working
Never
use
the
machine
should
be stored
for
use.
when
tired
in a
Werbung
